Sunday, June 9, 2019

This bulletin is supplied as technical information only and is not an authorization for repair.2020 Dodge or Ram Truck Grand Caravan Technical Service Bulletin # 08-059-12

Date: 121023

Body - Power Sliding Door Won't Close/Clicking Noises

NUMBER: 08-059-12

GROUP: Electrical

DATE: October 23, 2012

THIS BULLETIN SUPERSEDES SERVICE BULLETIN 08-045-11, DATED AUGUST 04.

2011 WHICH SHOULD BE REMOVED FROM YOUR FILES. THIS IS A COMPLETE

REVISION AND NO ASTERISKS HAVE BEEN USED TO HIGHLIGHT REVISIONS.

2020 Dodge or Ram Truck Grand Caravan V6-3.6L Page 16

HELP USING THE wiTECH DIAGNOSTIC APPLICATION FOR FLASHING AN ECU IS

AVAILABLE BY SELECTING "HELP" THEN "HELP CONTENTS" AT THE TOP OF

THE wiTECH DIAGNOSTIC APPLICATION WINDOW.

THE wiTECH SOFTWARE LEVEL MUST BE AT RELEASE 13.01 OR HIGHER TO

PERFORM THIS PROCEDURE.

SUBJECT:

Flash: Power Sliding Door Will Not Power Close And Makes A Clicking Noise

OVERVIEW:

This bulletin involves re-flashing the Power Sliding Door Module (PSDM) with updated software.

MODELS:

2011 (RT) Town and Country/Caravan

2012 (RT) Town and Country/Caravan

2013 (RT) Town and Country/Caravan

NOTE:

This bulletin applies to vehicles built prior to October 13, 2012 (MDH 1013XX) equipped with Right and left Power Sliding Doors (sales code

JRA/JRB).

SYMPTOM/CONDITION:

Customers may experience that the power sliding door will not power close. The sliding door will be stuck in the open position and the motor will

make a clicking noise. There are no stored Diagnostic Trouble codes (DTC's) in the power sliding door module for this issue. This will happen when

the PSDM loses the position counts. The sliding door will close manually using the inside or outside door handle. Flashing the PSDM will correct

this condition.

DIAGNOSIS:

1. Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in TechCONNECT, verify no DTC's are set. If DTCs are

present record them on the repair order and repair as necessary before proceeding further with this bulletin.

2. Using a Scan Tool (wiTECH) check the part number of the PSDM.

3. Is the PSDM part number 68079909AA?

a. Yes >>> Proceed to repair procedure, Step # 1.

b. NO >>> This bulletin doesn't pertain and normal diagnostic should be performed.

If the customer describes the symptom, perform the Repair Procedure.

REPAIR PROCEDURE:

NOTE:

Install a battery charger to ensure battery voltage does not drop below 13.2 volts. Do not allow the charging voltage to climb above 13.5 volts

during the flash process.

NOTE:

If this flash process is interrupted/aborted, the flash should be restarted.

1. Flash reprogram the PSDM. Help using the wiTECH Diagnostic Application for flashing the PSDM is made available through the wiTECH

Diagnostic Application. For instructions select the "HELP" tab on upper portion of the wiTECH window, then "HELP CONTENTS." This will

open the Welcome to wiTECH Help screen where help topics can be selected.

2. Has the PSDM part number update to 68079909AB?

a. Yes >>> Proceed to Step # 3.

b. NO >>> The module needs to be reprogrammed again. Proceed to the repair procedure, Step # 1.

NOTE:

If the PSDM has been flashed a number of times then this bulletin doesn't pertain and further diagnostics need to be performed.

3. Has both PSDM's been updated with the latest software?

a. Yes >>> Proceed to Step # 4.

b. No >>> Perform flash on the other PSDM, proceed to the repair procedure, Step # 1.

4. Clear any DTC's that may have been set in other modules due to reprogramming. The wiTECH application will automatically present all DTCs

2020 Dodge or Ram Truck Grand Caravan V6-3.6L Page 17

after the flash and allow the tech to clear them.

5. Perform the power sliding door relearn procedure in TechCONNECT, 08 - Electrical/8N - Power Systems/Power Sliding Door/Standard

Procedure, POWER SLIDING DOOR LEARN CYCLE.

POLICY:

Reimbursable within the provisions of the warranty.

No comments:

Post a Comment