Engine Controls - MIL ON, DTC P050B (Cold Start Cont.)

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Technical Service Bulletin # 12-018 Date: 120216

Engine Controls - MIL ON, DTC P050B (Cold Start Cont.)

Classification: EC12-002

Reference: NTB12-018

Date: February 16, 2012

2010-2012 ALTIMA WITH QR25DE FOR CALIFORNIA

MIL ON WITH P050B COLD START CONTROL

APPLIED VEHICLE: 2010-2012 Altima Sedan and Coupe (L32 and CL32)

APPLIED ENGINE: QR25DE (4-cyl engine) with California emissions only

IF YOU CONFIRM:

The MIL is ON with DTC P050B (Cold Start Control) stored in the ECM.

ACTION:

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 136

1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on.

2. If this bulletin applies, reprogram the ECM.

IMPORTANT:

The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE

PROCEDURE as it contains information that is essential to successfully completing this repair.

Service Procedure

NOTE:

^ Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed on the CONSULT PC screen.

^ If you are not familiar with the reprogramming procedure, refer to the "CONSULT- III plus (C-III plus) Reprogramming" general procedure.

^ Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learn (IAVL) conditions:

> Engine coolant temperature: 70-100锟斤拷C (158-212锟斤拷F)

> Battery voltage: More than 12.9V (At idle)

> Transmission: Warmed up

^ After reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learn, Accelerator Closed

Position, and DTC erase.

CAUTION

1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.

2. Open ASIST on the CONSULT PC and start C-III plus.

3. Wait for the plus VI to be recognized / connected.

^ Serial number will display when the plus VI is recognized / connected.

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 137

4. Select Re/programming, Configuration.

5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in Figure 2 above.

6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows.

A. Find the ECM Part Number and write it on the repair order.

NOTE:

This is the current ECM Part Number (P/N).

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 138

B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number column in Table A above.

^ If there is a match, this bulletin applies. Continue with the reprogramming procedure.

^ If there is not a match, this bulletin does not apply. Close C-III plus and refer to ASIST for further diagnostic information.

7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.

NOTE:

^ In some cases, more than one new P/N for reprogramming is available.

> In this case, the screen in Figure 3 displays.

> Select and use the reprogramming option that does not have the message "Caution! Use ONLY with NTBXX-XXX".

^ If you get this screen in Figure 3, and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle.

Close C-III plus and refer back to ASIST for further diagnosis.

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 139

8. When the screen in Figure 4 displays, reprogramming is complete.

NOTE:

If the screen in Figure 4 does not display (reprogramming does not complete), refer to the information below.

9. Disconnect the battery charger from the vehicle.

10. Select Next.

NOTE:

^ In the next steps below, you will perform Throttle Valve Closed Position, Idle Air Volume Learn, Accelerator Closed Position, and DTC

erase.

^ These operations are required before C-III plus will provide the final reprogramming confirmation report.

If reprogramming does not complete and the "!?" symbol displays as shown in Figure 5:

^ Check battery voltage (12.0 - 15.5V).

^ Ignition is ON, Ready Mode is OFF.

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 140

^ External Bluetooth(R) devices are OFF.

^ All electrical loads are OFF.

^ Select Retry and follow the on screen instructions.

NOTE:

Retry may not go through on first attempt and

If reprogramming does not complete and the "X" symbol displays as shown in Figure 6:

^ Check battery voltage (12.0 - 15.5V).

^ CONSULT A/C adapter is plugged in.

^ Ignition is ON, Ready Mode is OFF.

^ Transmission in Park.

^ All C-III plus / plus VI cables are securely connected.

^ All C-III plus updates are installed.

^ Select Home, and then restart the reprogram procedure from the beginning.

11. Follow the on-screen instructions to perform the following:

^ Throttle Valve Closed Position

^ Idle Air Volume Learn (IAVL)

NOTE:

^ Listed below are common conditions required for IAVL to complete.

^ If IAVL does not complete within a few minutes, a condition may be out of range.

^ Refer to the appropriate Electronic Service Manual (ESM) for specific conditions required for the vehicle you are working on.

> Engine coolant temperature: 70 - 100锟斤拷C (158 - 212锟斤拷F)

> Battery voltage: More than 12.9V (At idle)

> Selector lever: P or N

> Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)

> Steering wheel: Neutral (Straight-ahead position)

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 141

> Vehicle speed: Stopped

> Transmission: Warmed up

^ Accelerator Pedal Close Position Learning

^ Erase DTCs

12. When the entire reprogramming process is complete, the screen in Figure 7 will display.

13. Verify the before and after part numbers are different.

14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty documentation.

15. Select Confirm.

16. Close C-III plus.

17. Turn the ignition OFF.

18. Disconnect the plus VI from the vehicle.

19. Test drive the vehicle and make sure it operates correctly and the MIL is OFF.

^ If the MIL comes ON, go back to ASIST for further diagnostic information.

^ Diagnosis and repairs beyond ECM reprogramming are not covered by this bulletin.