Skip to main content

Disclaimer2010 Land Rover LR2 (LF) L6-3.2L Technical Service Bulletin # TECLTB002824 Date: 110204

Disclaimer2010 Land Rover LR2 (LF) L6-3.2L Technical Service Bulletin # TECLTB002824 Date: 110204



2010 Land Rover LR2 (LF) L6-3.2L Page 38



Body - Front And Rear Door Latch Diagnostic Information



NO: LTB00282 (Issue 4)



04 FEB 2011



ISSUE "4" CHANGES ARE HIGHLIGHTED IN GRAY



SECTION: 501



Front / Rear Side Door Latch Diagnostics



AFFECTED VEHICLE RANGE



CONDITION SUMMARY



PARTS:



No parts necessary; information only



TOOLS:



NOTE:



2003 - 2006 model year Range Rover (LM) vehicles must reference the 2007 - 2009 model year Range Rover (LM) Workshop Manual.



2010 Land Rover LR2 (LF) L6-3.2L Page 39



WARRANTY:



NOTE:



Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always



refer to DDW to obtain the latest repair time.



DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.



DIAGNOSTIC PROCEDURE



SYMPTOM DRIVEN SIDE DOOR LATCH DIAGNOSTICS



NOTE:



2003 - 2006 model year Range Rover (LM) vehicles must reference the 2007 - 2009 model year Range Rover (LM) Workshop Manual.



1. Refer to Workshop Manual, section 501-14: Handles, Locks, Latches and Entry Systems, and perform the appropriate diagnostics / repair

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...