Thursday, February 21, 2019

Multi AV System - Configuration After Replacing Control Unit

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Technical Service Bulletin # 10-033B Date: 120314



Multi AV System - Configuration After Replacing Control Unit



Classification: EL10-008B



Reference: NTB10-033B



Date: March 14, 2012



AV CONTROL UNIT REPLACEMENT REQUIRES CONSULT-III PLUS CONFIGURATION



This bulletin has been amended. The Applied Vehicles and Service Procedure sections have been revised. Please discard previous versions.



APPLIED VEHICLES:2010-2012 370Z Coupe and Roadster (H/Z34)



2010-2012 Altima Coupe, Sedan, and Hybrid (C/L32/HV)



2011-2013 GT-R (R35)



2010-2012 Maxima (A35)



2011-2012 Murano and Murano Cross Cabriolet (E/Z51)



2011-2012 Quest (E52)



SERVICE INFORMATION



If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason follow the steps in the Service Procedure to configure the Multi



AV system.



NOTE:



The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control



Unit until instructed.



Service Procedure



Before starting, make sure your ASIST has been freshly synchronized and all CONSULT-III (C-III) plus upgrades have been installed.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 107



Parts of the Procedure



PART 1:



Record Multi AV Configuration Values of Original AV Control Unit; Replace AV Control Unit



1. Make sure the shift selector is in Park, and the parking brake is set.



2. Connect the C-III plus VI to the vehicle.



3. Turn ON the ignition.



NOTE:



You may want to start the engine to keep the battery charged during this procedure.



4. Write down customers radio station presets. (Presets will be lost during this procedure.)



5. Launch CONSULT-III (C-III) plus on the CONSULT PC.



6. Select Re/programming Configuration.



7. Read the General Precaution.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 108



When finished, touch the "Confirmed instructions" box to insert a check mark, then select Next.



8. Select the Manual Selection (Vehicle Name) tab, then select the applicable Model and Year.



9. Select, Select.



10. Confirm the correct Model Name and Model Year are displayed.



When finished, select Confirm.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 109



11. After system call completes, confirm the correct VIN is displayed.



When finished, select Confirm.



NOTE:



If the VIN displayed is incorrect, input the correct VIN. When finished, select Confirm.



12. Select MULTI AV.



13. Select Read/Write Configuration.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 110



14. Select Before Replace ECU.



15. Confirm current configuration and write it down.



^ Configuration can also be printed with the Print Screen button or Screen Capture button.



NOTE:



Configurable options will differ between models. Your screen may look different.



16. Select Save.



NOTE:



If the configuration data cannot be saved, replace the AV Control Unit as instructed in the applicable Electronic Service Manual (ESM) and then



proceed to PART 3: Perform Multi AV Initialization shown below in this bulletin.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 111



17. Select End.



18. Replace the AV Control Unit as instructed in the applicable ESM.



PART 2:



Configure the Multi AV System



19. Perform steps 1-10.



20. Select Confirm.



21. Select After Replace ECU.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 112



22. Select OK.



After performing step 22



If an error message does not display:



^ Proceed to PART 5: Confirm Multi AV System Is Operational shown below in this bulletin.



If an error message does display:



^ Proceed to PART 3: Perform Multi AV Initialization, below.



PART 3 (if needed):



Perform Multi AV Initialization



NOTE:



Leave C-III plus running and the VI connected while performing Multi-AV initialization.



23. Turn OFF the audio system.



24. Put the AV system into System Diagnostic Mode as follows:



a. Press and hold the SETTING button (see Figure 14).



b. While holding the SETTING button, turn the volume control knob 40 clicks or more.



^ The volume control knob can be turned either direction.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 113



^ When the system goes into the System Diagnostic Menu, the screen in Figure 15 will display.



25. Select Confirmation/Adjustment.



26. Select Delete Unit Connection Log.



27. Select Yes.



28. Select Initialize Settings.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 114



29. Select Accessory Number Initialization.



30. Select Yes.



31. Wait while the system initializes.



^ The screen in Figure 21 will display while initializing.



^ The screen in Figure 22 will display when initialization is complete.



32. Once initialization is complete, reboot the Multi AV system as follows:



a. Turn OFF the ignition.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 115



b. Wait 10 seconds.



c. Turn ON the ignition.



Proceed to PART 4: Manually Configure the Multi AV System, below.



PART 4 (if needed):



Manually Configure the Multi AV System



NOTE:



If the screen in Figure 23 is not displayed, click on the Home icon.



33. Select Re/programming Configuration.



34. Read the General Precaution.



When finished, touch the "Confirmed instructions" box to insert a check mark, then select Next.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 116



35. Select the Manual Selection (Vehicle Name) tab, then select the applicable Model and Year.



36. Select, Select.



37. Confirm the correct Model Name and Model Year are displayed.



When finished, select Confirm.



38. Confirm the correct VIN is displayed.



When finished, select Confirm.



NOTE:



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 117



If the VIN displayed is incorrect, input the correct VIN. When finished, select Confirm.



39. Select MULTI AV.



40. Select Manual Configuration.



41. Use the drop down menus to select the Configuration options that were printed or written down in step 15.



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Hybrid Page 118



^ Configurable options will differ between models. Your screen may look different from Figures 30 and 31.



42. Select Next.



43. Confirm the configuration displayed is correct, then select OK.



44. Start the engine and let it idle briefly.



45. Use C-III plus to clear any codes from the Multi AV system.



a. Select Diagnoses (One System)> Multi AV> Self Diagnosis Results.



b. Clear any codes that may be present.



46. Close C-III plus and disconnect the VI from the vehicle.



PART 5:



Confirm Multi AV System Is Operational



47. Put your toot on the brake, start the engine, and move the shift selector to R (reverse).



48. If equipped, make sure the rear view monitor is working correctly.



49. Put the shift selector back into Park.



50. Turn ON the radio.



51. Turn the volume knob and make sure the audio volume responds to movement of the knob.

No comments:

Post a Comment