CVT - Output Speed Sensor Service

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Technical Service Bulletin # 11-042 Date: 110420

Classification: AT11-007

Reference: NTB11-042

Date: April 20, 2011

2007-2011 ALTIMA, JUKE, ROGUE, SENTRA; CVT OUTPUT SPEED SENSOR SERVICE

APPLIED VEHICLES:

2007-2011 Altima (C/L32) QR25 ONLY

2011 Juke (F15)

2008-2011 Rogue (S35)

2007-2011 Sentra (B16) MR20 & QR25 ONLY

SERVICE INFORMATION

If the Output Speed Sensor has been removed and replaced for any reason:

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 316

NOTE:

Input/Turbine Speed Sensor does not require shims. That Sensor is flush mounted to CVT casting.

The correct number of spacer shims must be installed between the Sensor and the CVT body.

Refer above for shim number application chart.

SERVICE PROCEDURE

1. Determine required number of shims by model:

2. Assemble the Output Speed Sensor with the proper 0-ring.

3. Place bolt with attached washers through hole on the Sensor.

4. After determining the correct number of washers for the vehicle, place the shims over the portion of the bolt that is exposed below the sensor

body.

5. Assemble as seen below: Torque retaining bolt to 5.9 Nm (0.6 kg-m, 52 in-lb)

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 317

Comments

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: A80 (Intelligent servo module for DIRECT SELECT) Affected functions: Drive position selection Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:270641Possible cause and remedy Internal fault in control unit Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**: - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**: - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**: - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**: - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...

Mercedes Benz

Search This Blog