Skip to main content

Tire Monitor System - TPMS Lamp Diagnostic Info.

2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Technical Service Bulletin # 09-101B Date: 111003



Tire Monitor System - TPMS Lamp Diagnostic Info.



Classification: WT09-004B



Reference: NTB09-101B



Date: October 3, 2011



TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT DIAGNOSTIC PROCEDURE



This bulletin has been amended. Changes were made. Please discard previous versions.



APPLIED VEHICLES: All Nissan vehicles with Tire Pressure Monitoring System (TPMS)



IF YOU CONFIRM



The TPMS warning light is illuminated (continuously or flashing),



2010 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 208



ACTIONS



STEP 1: Turn ignition to "OFF" and then "ON" position (engine not required to be running).



^ If the TPMS warning light is continuously illuminated (not flashing), the TPMS is operating normally and has detected low tire pressure in one of



the tires. Go to STEP 2.



NOTE:



> Normal tire pressure maintenance is not covered under warranty.



> Some 2011 and newer models will display an alert in the Vehicle information display near the speedometer. The alert will read "Check Tire



Pressure", or similar, and will accompany the illuminated TPMS light.



> If the TPMS warning light is flashing for approximately one minute, there is a TPMS system malfunction. Do not go to Step 2. Instead, check



the DTC and refer to the Service Manual for repair instructions.



STEP 2: Leave the ignition in the "ON" position* (engine is not required to be running) and set the tire pressure to the recommended pressure.



^ Refer below for Important Tire Pressure Information.



* Leaving the ignition in the ON position may allow the TPMS to detect the corrected tire pressure more quickly on 2009 and newer models



(WITHOUT having to drive the vehicle).



Important Tire Pressure Information:



Each vehicle is equipped with a "Tire and Loading Information" placard (see example in Figure 1).



For factory equipped tires, follow the recommended cold pressure on the placard to set the tire pressure on the vehicle.



Tire pressure can be affected by factors such as tire temperature, outside temperature, time, and altitude.



^ Refer to NTB08-033 for additional information about these factors that affect tire pressure, including seasonal temperature changes.



When tire pressure is low, make sure it is not caused by a leak. If needed, repair as necessary.



After tires are inflated to the recommended pressure, the vehicle may need to be driven at speeds above 16 mph for the TPMS to turn off the low tire



pressure warning light. DO NOT USE CONSULT TO RESET THE TPMS.



For additional Tire Pressure Information, refer to NTB08-033 (Tire Pressure Information).

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...