2010 Mercedes Benz Truck GL 350 BLUETEC (164.825) V6-3.0L DSL Turbo (642.820)
Vehicle: All Technical Service Bulletins
Steering - Noises and Guidelines for Detection
Noises from the steering system (guidelines for detecting noise)
Topic number L146.20-P-055943
Version 1
Design group 46.20 Steering gear
Date 04-24-2013
Validity Model 164/251
Reason for change
Complaint:
1.) Rattling noises from the area of the steering column tube on rough roads or when driving over road bumps
2.) Cracking noises when braking or accelerating, which may also be perceptible at the steering wheel at the same time
3.) Rattling noises from the area of the steering gear on rough roads or when driving over road bumps
Cause:
1.) Play or incorrectly engaged firewall pivot point
2.) Play or incorrectly engaged firewall pivot point, or slip/stick effect of steering coupling
3.) Play between thrust piece and toothed rack of steering
Attachments
Remedy:
For noise diagnosis the use of the STEELMAN ChassisEAR is helpful and it must always be used if there is any uncertainty in order to clearly
identify the cause of the noise.
Re. causes 1 and 2:
Check version of firewall pivot point and check for play:
2010 Mercedes Benz Truck GL 350 BLUETEC (164.825) V6-3.0L DSL Turbo (642.820)
a) Check the version -> If an old version (see Figure 001 version "2" or Figure 002 version "4") is installed, the current version (see Figure 001
version "3" or Figure 002 version 3) must be installed.
The new version of the firewall pivot point is installed in production as of VIN 164.### - # A - 220353 or 251.### - # A - 053080.
2010 Mercedes Benz Truck GL 350 BLUETEC (164.825) V6-3.0L DSL Turbo (642.820)
b) Check that the bearing is installed without play and properly engaged -> A white stripe must be visible (see Figures 003 and 004).
Note:
Also refer to the TIPS document "Cracking noises from the area of the steering shaft".
Re. cause 2:
Check steering coupling slip/stick effect:
2010 Mercedes Benz Truck GL 350 BLUETEC (164.825) V6-3.0L DSL Turbo (642.820)
- Remove steering coupling - Push steering coupling together in sliding piece and pull apart; if a pressure point can be felt, the coupling must be
replaced
Re. cause 3:
Check play between thrust piece and toothed rack of steering. and adjust if necessary:
- Check steering effect with simplified test method, see TIPS document "Rattling/thumping noises from the area of the steering (simplified test
method)" L146.20-P-053398
- Adjust play between thrust piece and steering rack if necessary
Symptoms
WIS-References
Mercedes-Benz, Luxury Automobiles, German Engineering, Premium Car Brand, Mercedes Innovation
Popular Posts
-
P179A77 The redundancy system for DIRECT SELECT has a malfunction. The commanded position cannot be reached. Possible cause: A80 (Inte...
-
Love For Cars The 2008 model may not look too different to the previous Accord, but under the surface, it is indeed all-new. The styling isn...
-
Vehicle: All Technical Service Bulletins Diesel Engine - Crackling/Ticking Noise At Idle Engine makes intermittent knocking noise, ticking...
-
$102.25 End Date: Sunday Jul-28-2019 13:37:55 PDT Buy It Now for only: $102.25 Buy It Now | Add to watch list
-
You don't need a supercar to have cool doors. There’s far more to a supercar than something as superficial as a cool pair of doors. But,...
-
$75.97 End Date: Sunday Jul-7-2019 11:44:55 PDT Buy It Now for only: $75.97 Buy It Now | Add to watch list
-
Bendix TitaniuMetallic2 Brake Pads are completely reformulated with TitaniuMetallic2 blue coating and is more effective during...
-
P0108 B28 (Pressure sensor) : Short circuit to positive or open circuit (P0108) Possible cause: B28 (Pressure sensor) Affected functi...
-
The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DI...
-
As of the latest 2025-2026 Tesla lineup, the cheapest Tesla you can buy new is the **Tesla **Model 3 Standard trim — an entry-level versi...
Popular Posts
-
P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 A...
-
P2505 Relay 'Circuit 87' ( Engine ) (P2505) Possible cause: N3/10 (MESFI [ME] control unit) K40/4kK (Engine electronics an...
-
C426 Start enable 'Drive authorization system' not issued. Possible cause: Engine management Affected functions: ...
-
Misfiring of cylinder 4 : Damages TWC (P0304) Misfiring of cylinder 4 : Damages TWC (P0304) Possible cause: Combustion misfirings Aff...
-
Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Ch...
-
2010 Mercedes Benz Truck GL 350 BLUETEC (164.825) V6-3.0L DSL Turbo (642.820) Vehicle: All Technical Service Bulletins COMAND(R) - 'Dr...
-
2010 Mercedes Benz C 63 AMG Sedan (204.077) V8-6.3L (156.985) Vehicle: Customer Interest ABS/TCS - ABS Lamp ON/Codes 5603/5410 Set Y...
-
D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil ...
-
P179A77 The redundancy system for DIRECT SELECT has a malfunction. The commanded position cannot be reached. Possible cause: A80 (Inte...
-
P0108 B28 (Pressure sensor) : Short circuit to positive or open circuit (P0108) Possible cause: B28 (Pressure sensor) Affected functi...
Popular Posts
-
P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 A...
-
D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil ...
-
Vehicle: All Technical Service Bulletins Diesel Engine - Crackling/Ticking Noise At Idle Engine makes intermittent knocking noise, ticking...
-
Mercedes-Benz Mercedes Benz OEM Parts Mercedes Benz OE Replacement Parts Technical Service Bulletin # LI83-30_P-05363...
-
Okay, so I need to figure out the financial results for Tesla's second quarter of 2025 based on the information provided. Let me start...
-
P179A77 The redundancy system for DIRECT SELECT has a malfunction. The commanded position cannot be reached. Possible cause: A80 (Inte...
-
Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Ch...



