Mercedes-Benz, Luxury Automobiles, German Engineering, Premium Car Brand, Mercedes Innovation
Thursday, September 30, 2021
GMC Sierra 1500 vs. GMC Sierra HD: Visual Comparison
2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 654
- Measure direct current with multimeter between sockets [F.98] 2 and [F.19] 115 of the 126-pole socket box tester.
Specified value
- Voltage[11.0...15.0] V
Question
- Is the measurement value OK?
YES
The measurement value is OK.Further possible causes of fault
- M33 (electric air pump)
End of test
NO
The measurement value is not OK.Possible cause and remedy
- Voltage supply of component N10/1kR (Air pump or oil cooler fan relay)
- N10/1kR (Air pump or oil cooler fan relay)
- Lines to component M33 (electric air pump)
- M33 (electric air pump)
End of test
NO
The measurement value is not OK.Possible cause and remedy
- Lines to component N10/1kR (Air pump or oil cooler fan relay)
- N10/1kR (Air pump or oil cooler fan relay)
End of test
3. Check component Y32 (Air pump switchover valve).
Test 3.1: Test actuation of component Y32 (Air pump switchover valve).
Test 3.2: Test current consumption of component Y32 (Air pump switchover valve).
3.1. Test actuation of component Y32 (Air pump switchover valve).
Test sequence
- Switch on ignition.
- Actuate component Y32 (Air pump switchover valve).(Proceed to 'Actuation' with F2)
Warning!Communication with ECU required.
3.2. Test current consumption of component Y32 (Air pump switchover valve).
Figure legend
- A -ConnectionTest cable 35-pin socket box
- 001 -Sockets of component N3/10 (ME-SFI [ME] control unit)
- 05 -35-pin socket box
- 050 -126-pin socket box
- 108 -Test cable 266 589 01 63 00
- N3/10 (ME-SFI [ME] control unit)
- II 1-63ConnectionTest cable
- III 64-126ConnectionTest cable
Warning!
- Connection A of test cable 108 may NOT be connected to connection B of the 126-pin socket box (050).
Continue to test with button F2
2010 Cadillac Truck SRX FWD V6-3.0L Page 120
2010 Cadillac Truck SRX FWD V6-3.0L Page 120
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B0014 01
- Driver Seat Side Air Bag Deployment Loop Short to Battery
DTC B0014 02
- Driver Seat Side Air Bag Deployment Loop Short to Ground
DTC B0014 04
- Driver Seat Side Air Bag Deployment Loop Open
DTC B0014 0D
- Driver Seat Side Air Bag Deployment Loop High Resistance
DTC B0014 0E
- Driver Seat Side Air Bag Deployment Loop Low Resistance
DTC B0015 01
- Driver Seat Belt Retractor Pretensioner Deployment Loop Short to Battery
DTC B0015 02
- Driver Seat Belt Retractor Pretensioner Deployment Loop Short to Ground
DTC B0015 04
- Driver Seat Belt Retractor Pretensioner Deployment Loop Open
DTC B0015 0D
- Driver Seat Belt Retractor Pretensioner Deployment Loop High Resistance
DTC B0015 0E
- Driver Seat Belt Retractor Pretensioner Deployment Loop Low Resistance
DTC B0016 01
- Left Roof Rail Air Bag Deployment Loop Short to Battery
DTC B0016 02
- Left Roof Rail Air Bag Deployment Loop Short to Ground
DTC B0016 04
- Left Roof Rail Air Bag Deployment Loop Open
DTC B0016 0D
- Left Roof Rail Air Bag Deployment Loop High Resistance
DTC B0016 0E
- Left Roof Rail Air Bag Deployment Loop Low Resistance
DTC B0019 01
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Short to Battery
DTC B0019 02
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Short to Ground
DTC B0019 04
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Open
DTC B0019 0D
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 High Resistance
DTC B0019 0E
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Low Resistance
DTC B0020 01
- Passenger Instrument Panel Air Bag Deployment Loop Stage 2 Short to Battery
Which is better RAM or tundra?
In comparison to the new Toyota Tundra, the Ram 1500 gives you more power and capability. ... While the new Toyota Tundra also comes equipped with a 5.7-Liter HEMI V8 Engine it only produces 381 horsepower and 401 lb. -ft of torque. Even more surprising the new Toyota Tundra has a maximum towing capacity of 10,200 lbs.2020 RAM 1500 vs 2020 Toyota Tundra Comparison Review ...
2022 Nissan Frontier Rally Truck Has NISMO Off-Road Parts, Retro Livery
This one-off Frontier Pro-4X wears a red, white, and blue wrap inspired by '80s Nissan off-road racers and will compete in the all-female Rebelle Rally.
from Latest Content - Car and Driver https://ift.tt/3imJzwO
Tested: The 2021 Porsche Panamera 4S Exists for the EV Resistance
The Panamera can be confused with the all-electric Taycan, but the 443-hp 4S hatchback is a desirable four-door for those who aren't ready to adopt an EV.
from Latest Content - Car and Driver https://ift.tt/3F7mrMj
2022 Land Rover Discovery
Review, Pricing, and Specs
from Latest Content - Car and Driver https://ift.tt/3kmfbRu
2010 Cadillac Truck SRX FWD V6-3.0L Page 90
2010 Cadillac Truck SRX FWD V6-3.0L Page 90
* The SDM requests the instrument cluster to illuminate the AIR BAG indicator.
* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.
Conditions for Clearing the DTC
* The condition for setting the DTC no longer exists.
* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
Diagnostic Aid
Note: The following diagnostic aids apply for both current and history DTCs.
An incorrectly installed CPA or incorrectly seated connector can cause a shorting bar to short both control circuits together. Check the connectors
and CPAs if a DTC with symptom byte 02 or 0E is set, to ensure the shorting bars are not causing the circuits to be shorted together. Shorting bars
are used in the locations listed below:
* Passenger instrument panel air bag
* Driver and passenger seat side air bags
* Left and right roof rail air bags
* Driver and passenger seat belt retractor pretensioners
* SDM
* Inline connectors - on the side of the harness connector
* Harness side of the SDM connector
Terminal fretting or incorrectly seated connector can cause an open/high resistance condition. Check the circuit terminals for fretting or incorrectly
seated connector if a DTC with symptom byte 04 or 0D is set. If DTCs of deployment loops which are in the seat DTC B0014 and B0021, can
occur because of stress or damage to the harness due to seat movement. Move the seat to the full extend of travel while using the scan tool to
observe deployment type loop parameters.
If the pretensioner, passenger instrument panel or side air bag has inflated under unexpected conditions and/or DTC with symptom byte 01 is set,
check both control circuits for a short to voltage.
Reference Information
Schematic Reference
SIR Schematics (See: Diagrams/Electrical Diagrams/Air Bag Systems)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Description and Operation
SIR System Description and Operation (See: Restraints and Safety Systems/Air Bag Systems/Description and Operation/SIR System)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Note:
* Refer to SIR Service Precautions (See: Restraints and Safety Systems/Air Bag Systems/Service Precautions/Technician Safety Information).
* Inspect all terminals for damage or corrosion when disconnecting connectors. Damage or corrosion in the following requires repair or
replacement of the affected component/connector.
- Seat belt retractor pretensioner
- Passenger instrument panel air bag
2021 Jeep Grand Cherokee L Vs. 2022 Wagoneer: Which Has the Better Row Setup?
2022 GMC Yukon gets larger screen, standard power sliding console
Continue reading 2022 GMC Yukon gets larger screen, standard power sliding console
2022 GMC Yukon gets larger screen, standard power sliding console originally appeared on Autoblog on Thu, 30 Sep 2021 14:15:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsGetting Our Model 3 Approved for Tesla's FSD Beta Requires a Passing Safety Score
Tesla CEO Elon Musk says drivers who requested Full Self-Driving Beta will be granted access on October 9 if their Safety Score checks out.
from Latest Content - Car and Driver https://ift.tt/3zY9Bwn
2022 Mercedes-Benz GLE-Class
Review, Pricing, and Specs
from Latest Content - Car and Driver https://ift.tt/2FRMiKX
This popular car vacuum has over 100,000 5-star ratings on Amazon
Filed under: Commerce
Continue reading This popular car vacuum has over 100,000 5-star ratings on Amazon
This popular car vacuum has over 100,000 5-star ratings on Amazon originally appeared on Autoblog on Thu, 30 Sep 2021 13:30:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsDoes Kia K5 hold its value?
2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 1393
- [11...14 V]
Question
- Is the measurement value OK?
YES
The measurement value is OK.Note
- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose
contact and corrosion..
End of test
NO
The measurement value is not OK.Possible cause and remedy
- Lines to component N51 (AIRmatic with ADS control module)
- N10/1f45 (Fuse 45)
End of test
1.1.3.2.1.8.2.3. Test procedure ground cable
Test prerequisite
- Battery voltage is OK.
Test sequence
- Switch off ignition.
- Connect socket box.
- W15/Measure resistance with multimeter between 1 and (2.21) 55 of the 35-pole socket box tester.
Specified value
- [<1ohms]
Question
- Is the measurement value OK?
YES
The measurement value is OK.Note
- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose
contact and corrosion..
End of test
NO
The measurement value is not OK.Possible cause and remedy
- Ground cable
- W15/1 (Ground (right footwell))
End of test
1.1.3.2.1.9. Check power supply at control unit N63/1 (DTR control module).
Check power supply at control unit N63/1 (DTR control module).
Test sequence
- Switch off ignition.
- Disconnect coupling 2 at component N63/1 (DTR control module).
- Measure direct voltage with multimeter between sockets (N63/1) 2.8 and (N63/1) 2.4
2021 Chevy Tahoe Diesel, Chevy Suburban Diesel Demand Steady At Six Percent
2022 Alfa Romeo Giulia, Stelvio get more safety, convenience features
Filed under: Alfa Romeo,Crossover,Luxury,Sedan
Continue reading 2022 Alfa Romeo Giulia, Stelvio get more safety, convenience features
2022 Alfa Romeo Giulia, Stelvio get more safety, convenience features originally appeared on Autoblog on Thu, 30 Sep 2021 12:30:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsSquirrel stashes 42 gallons of walnuts in a Chevrolet Avalanche
Filed under: Weird Car News
Continue reading Squirrel stashes 42 gallons of walnuts in a Chevrolet Avalanche
Squirrel stashes 42 gallons of walnuts in a Chevrolet Avalanche originally appeared on Autoblog on Thu, 30 Sep 2021 11:40:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsChevrolet Corvette Z06 convertible apparently caught in spy photos
Filed under: Spy Photos,Chevrolet,Convertible,Future,Performance
Continue reading Chevrolet Corvette Z06 convertible apparently caught in spy photos
Chevrolet Corvette Z06 convertible apparently caught in spy photos originally appeared on Autoblog on Thu, 30 Sep 2021 11:20:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | Comments2010 Cadillac Truck SRX FWD V6-3.0L Page 346
2010 Cadillac Truck SRX FWD V6-3.0L Page 346
B319A 02
The BCM has detected the right rear window switch is active for greater than 60 seconds
B316B 39, B317A 39, B318A 39, B319A 39
The BCM has detected an internal failure within the affected door switch
Action Taken When the DTC Sets
The affected power window will malfunction.
Conditions for Clearing the DTC
B316B 00, B316B 02, B317A 02, B318A 02, B319A 02
* The DTC will be current for as long as the fault is present.
* The DTC will change from current to history when the fault is no longer present.
* A history DTC will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present.
B316B 39, B317A 39, B318A 39, B319A 39
If the DTC is current, the affected window switch must be replaced before the DTC can be cleared.
Reference Information
Schematic Reference
Moveable Window Schematics (See: Windows and Glass/Windows/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Description and Operation
Power Windows Description and Operation (See: Windows and Glass/Windows/Description and Operation/Power Windows)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, verify that each of the scan tool parameters listed below are Inactive:
* Front Passenger Main Control Down Switch
* Front Passenger Main Control Express Switch
* Front Passenger Main Control Up Switch
* Left Rear Window Main Control Down Switch
* Left Rear Window Main Control Express Switch
* Left Rear Window Main Control Up Switch
* Right Rear Window Main Control Down Switch
* Right Rear Window Main Control Express Switch
* Right Rear Window Main Control Up Switch
瀚慖f any of the parameters are always Active, replace the S79D window switch-driver.
2. Verify that the scan tool Left Rear Window Switch at Door parameter is Inactive.
瀚慖f not the specified value, replace the S79LR window switch-left rear.
3. Verify that the scan tool Right Rear Window Switch at Door parameter is Inactive.
Nissan Note Aura Nismo launches with sporty-looking electric powertrain
Pagani Huayra Roadster BC First Drive: When Too Much Is Just Right
Pagani Huayra Roadster BC First Drive: When Too Much Is Just Right
via https://youtu.be/LHiCU4fj_pU
Genesis GV60 gets a Drift mode and up to 429 horsepower
Filed under: Green,Genesis,Technology,Crossover,Electric,Luxury,Performance
Continue reading Genesis GV60 gets a Drift mode and up to 429 horsepower
Genesis GV60 gets a Drift mode and up to 429 horsepower originally appeared on Autoblog on Thu, 30 Sep 2021 11:05:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | Comments2022 Mercedes-AMG GLA-Class
Review, Pricing, and Specs
from Latest Content - Car and Driver https://ift.tt/3CoGWmG
2023 Genesis GV60 EV Will Offer AWD, Up to 429 HP, Lots of Tech
The luxury brand's first EV is set to arrive in the U.S. in 2022, and the specs are similar to the Hyundai Ioniq 5 and Kia EV6.
from Latest Content - Car and Driver https://ift.tt/3AYCmtY
2021 Harley-Davidson Pan America 1250 First Ride | Making a statement
Filed under: First Ride,Motorcycle,Luxury,Off-Road,Performance
Continue reading 2021 Harley-Davidson Pan America 1250 First Ride | Making a statement
2021 Harley-Davidson Pan America 1250 First Ride | Making a statement originally appeared on Autoblog on Thu, 30 Sep 2021 10:00:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsJapanese manufacturing output extends declines on car production cuts
Filed under: Earnings/Financials,Plants/Manufacturing
Continue reading Japanese manufacturing output extends declines on car production cuts
Japanese manufacturing output extends declines on car production cuts originally appeared on Autoblog on Thu, 30 Sep 2021 09:43:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsWatch Ducati unveil the first of six new motorcycles live right here
Filed under: Motorcycle
Continue reading Watch Ducati unveil the first of six new motorcycles live right here
Watch Ducati unveil the first of six new motorcycles live right here originally appeared on Autoblog on Thu, 30 Sep 2021 09:04:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsHow GM's Ultifi software will change the buying and ownership experience
Filed under: GM,Technology
Continue reading How GM's Ultifi software will change the buying and ownership experience
How GM's Ultifi software will change the buying and ownership experience originally appeared on Autoblog on Thu, 30 Sep 2021 08:49:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsSlew of Ford recalls affect more than a million vehicles
Filed under: Recalls,Ford,Lincoln,Safety,Truck,Coupe,Crossover,SUV,Luxury
Continue reading Slew of Ford recalls affect more than a million vehicles
Slew of Ford recalls affect more than a million vehicles originally appeared on Autoblog on Thu, 30 Sep 2021 08:29:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsHonda is working on small rockets, electric aircraft and robots for the Moon
Filed under: Honda,Transportation Alternatives,Emerging Technologies,Space
Continue reading Honda is working on small rockets, electric aircraft and robots for the Moon
Honda is working on small rockets, electric aircraft and robots for the Moon originally appeared on Autoblog on Thu, 30 Sep 2021 08:00:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | Comments2010 Cadillac Truck SRX AWD V6-3.0L Page 1751
2010 Cadillac Truck SRX AWD V6-3.0L Page 1751
* Control Valve Lower Body and Upper Body Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Valve
Body/Service and Repair/6T70/6T75 - Automatic Transmission/Control Valve Lower Body and Upper Body Replacement)
* Low and Reverse Clutch and 1-2-3-4 Clutch Plate Removal (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service
and Repair/Overhaul/8. Low and Reverse Clutch and 1-2-3-4 Clutch Plate Removal) and 3-5-Reverse and 4-5-6 Clutch Housing Disassemble
(See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and Repair/Overhaul/41. 3-5-Reverse and 4-5-6 Clutch
Housing Disassemble)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,
setup, and programming
P0797
DTC P0796 or P0797
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0796
- Clutch Pressure Control (PC) Solenoid 3 - Stuck Off
DTC P0797
- Clutch Pressure Control (PC) Solenoid 3 - Stuck On
Circuit/System Description
The clutch pressure control (PC) solenoid 3 is part of the control solenoid valve assembly, which has no serviceable components. The PC solenoid
3 regulates transmission fluid pressure (TFP) to the R1/4-5-6 clutch regulator valve which controls pressure to the low and reverse clutch and the
4-5-6 clutch. The transmission control module (TCM) calculates gear ratio based on the RPM signals from the input speed sensor (ISS) and the
output speed sensor (OSS). The TCM compares the expected transmission gear ratio to the calculated gear ratio for each commanded gear.
Conditions for Running the DTC
P0796 or P0797
* No ISS DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206,
P0207, P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, or P182E.
* The ignition voltage is greater than 8.6 volts.
* The engine speed is greater than 400 RPM for 5 seconds.
* The output speed is 16 RPM or greater, or the throttle position is 0.4 percent or greater.
* The throttle position signal is valid.
* The high side driver is commanded on.
* The transmission fluid temperature is 0掳C (32掳F) or greater.
Conditions for Setting the DTC
P0796
The TCM detects an incorrect ON-coming clutch gear ratio or shift flare when the R1 or 4-5-6 clutch is commanded on.
P0797
The TCM detects an incorrect OFF-going clutch gear ratio or shift tie-up when the R1 or 4-5-6 clutch is commanded off.
Action Taken When the DTC Sets
P0796
* DTC P0796 is a Type A DTC.
* The TCM commands maximum line pressure.
* The TCM freezes transmission adaptive functions.
* The TCM inhibits Tap Up/Down function.
* The TCM inhibits manual shifting of forward gears.
* The TCM limits the transmission to 1st, 3rd, or reverse operation.
All of the Bond cars of 'No Time To Die' (caution for spoilers)
Filed under: Celebrities,TV/Movies,Aston Martin,Chevrolet,Jaguar,Land Rover,Maserati,Toyota,Bikes,Hybrid,Luxury,Off-Road,Performance,Supercars,Classics
Continue reading All of the Bond cars of 'No Time To Die' (caution for spoilers)
All of the Bond cars of 'No Time To Die' (caution for spoilers) originally appeared on Autoblog on Thu, 30 Sep 2021 07:00:00 EDT. Please see our terms for use of feeds.
Permalink | Email this | CommentsThe 1578-Horsepower Bugatti Chiron Super Sport Is Peak Engine
We hit the track to experience what may be the most powerful internal-combustion production car ever.
from Latest Content - Car and Driver https://ift.tt/3mf6Kdo
Alternator Part Number: 013-154-06-02-87
2010 Cadillac Truck SRX FWD V6-3.0L Page 224
2010 Cadillac Truck SRX FWD V6-3.0L Page 224
3. Test for infinite resistance between the following terminals:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
瀚慖f not the specified value, replace the KR73 RUN/CRNK relay.
4. Test for less than 2 ohm between terminals 30 and 87A.
瀚慖f greater than the specified range, replace the KR73 RUN/CRNK relay.
5. Install a 3 A fused jumper wire between the relay terminal 85 and 12 V. Install a jumper wire between the relay terminal 86 and ground. Test
for less than 2 ohm between terminals 30 and 87.
瀚慖f greater than specified range, replace the KR73 RUN/CRNK relay.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay
Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power
Distribution Relay/Service and Repair/Relay Replacement (Within an Electrical Center))
* Control Module References (See: Testing and Inspection/Programming and Relearning)for the steering column lock control module
replacement, setup and programming
B147E
DTC B147E
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptor
DTC B147E 02
- Battery Saver Relay Set Secondary Circuit Short to Ground
Diagnostic Fault Information
Circuit/System Description
The battery saver mode reduces the parasitic load of some modules during overseas shipment or during vehicle storage conditions. This improves
the drain time on the battery (up to 70 days without the battery going dead). When the vehicle is in transport/storage, some features may have
reduced functionality while in the battery saver mode, such as disabling the Remote Function Actuator or content theft features.
The battery saver mode incorporates a latching relay that when enabled disconnects some modules from their ignition off power or memory power
sources. For vehicles built before the mid-year 2010 model year or not flashed with 2010 model year, or newer, software, battery saver mode is
initiated by starting the vehicle and then turning the ignition key into the crank position or pushing the push button start switch (if equipped) for
greater than 15 seconds. For vehicles built after the mid-year 2010 model year or flashed with 2010 model year, or newer, software, battery saver
mode is initiated by turning on the hazard flashers, starting the vehicle, and then turning the ignition key into the crank position or pushing the push
button start switch (if equipped) for greater than 15 seconds. The mode is disengaged by repeating the previous process causing the relay to latch in
the other direction. This feature can be used as many times as necessary if the vehicle is to be stored for an extended period of time.
Conditions for Running the DTC
* The system voltage is between 9-16 V.
"What's the worst car brand?The list of the worst car brands for reliability:Jaguar F-Pace.Volvo XC90.GMC Sierra 1500.Fiat 500L, Fiat 500X.Jeep Renegade.Dodge Dart, Dodge Journey.Infiniti Q50.Subaru WRX.More items...?Sep. 8, 202010 Worst Car Brands and Cars (Updated In 2020) - Car Logos"
"What's the worst car brand?The list of the worst car brands for reliability:Jaguar F-Pace.Volvo XC90.GMC Sierra 1500.Fiat 500L, Fiat 500X.Jeep Renegade.Dodge Dart, Dodge Journey.Infiniti Q50.Subaru WRX.More items...?Sep. 8, 202010 Worst Car Brands and Cars (Updated In 2020) - Car Logos"
2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 2198
- X30/5 (Left voltage distributor (CAN) connector)
- Test connectors and wiring for CAN of engine compartment CAN control modules.
- Control unit
Communication with ECU required ( Measuring system )
1.1.3.4. Display CAN signals with the aid of the special tool 'Star Diagnosis CANtool'.
Important notes
- When CAN diagnosis is finished, the 8-pin CAN cable must be replaced with the diagnostic cable.
- Before values are read out from a control unit, the control unit must be reinitialized.
Continue with button F2
Test 1.1.3.4.1: Actual values via CAN ( Engine CAN bus )
1.1.3.4.1. Actual values via CAN ( Engine CAN bus )
Note
- The actual values shown on the following screens are only displayed and updated as long as the CAN bus is active.
Continue with button F2
Test 1.1.3.4.1.1: Function-specific actual values :
Test 1.1.3.4.1.2: Cruise control
Test 1.1.3.4.1.3: Drive authorization
Test 1.1.3.4.1.4: Control unit-specific actual values :
Test 1.1.3.4.1.5: Electronic selector module
Test 1.1.3.4.1.6: Transmission control
Test 1.1.3.4.1.7: Motor electronics
Test 1.1.3.4.1.8: Steering column module
1.1.3.4.1.1. Function-specific actual values :
1.1.3.4.1.1. No further information available.
1.1.3.4.1.2. Cruise control
Warning!Communication with ECU required.
1.1.3.4.1.3. Drive authorization
Warning!Communication with ECU required.
1.1.3.4.1.4. Control unit-specific actual values :
1.1.3.4.1.4. No further information available.
1.1.3.4.1.5. Electronic selector module
Warning!Communication with ECU required.
1.1.3.4.1.6. Transmission control
Warning!Communication with ECU required.
1.1.3.4.1.7. Motor electronics
Warning!Communication with ECU required.
What is the difference between TrailBlazer and TrailBlazer EXT?
What is the difference between TrailBlazer and TrailBlazer EXT?
The TrailBlazer EXT is 207.8 inches long overall and rides on a 129-inch wheelbase. In contrast, the regular-length TrailBlazer rides a 113-inch wheelbase and measures 191.8 inches long. At 77.1 inches, the EXT stands 2.6 inches taller than the regular TrailBlazer. A sunroof is available.2006 Chevrolet TrailBlazer EXT Specs, Price, MPG & Reviews ...
2022 Toyota Tundra vs. 2021 Tacoma: Full Specs Comparison
2010 Cadillac Truck SRX AWD V6-3.0L Page 1645
2010 Cadillac Truck SRX AWD V6-3.0L Page 1645
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0667
- Transmission Control Module (TCM) Temperature Sensor Performance
DTC P0668
- Transmission Control Module (TCM) Temperature Sensor Circuit Low Voltage
DTC P0669
- Transmission Control Module (TCM) Temperature Sensor Circuit High Voltage
Circuit/System Description
The transmission control module (TCM) temperature sensor is located inside of the control solenoid valve assembly, which has no serviceable
components. The TCM temperature sensor provides the temperature of the TCM. This temperature reading is used in various shifting and
diagnostic routines in the TCM software. This fault is handled inside the TCM and no external circuits are involved.
Conditions for Running the DTC
P0667
* No DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207,
P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0658, P0668, P0669, P06AD, P06AE, P0712,
P0713, P0716, P0717, P0722, P0723, P0962, P0963, P0966, P0967, P0970, P0971, P215C, P2720, P2721, P2729, or P2730.
* Brake torque is not active.
* The engine speed is greater than 400 RPM for 5 seconds or greater.
* The ignition voltage is 8.6 volts or greater.
P0668
* DTC P0668 has set this ignition cycle.
* The engine speed is greater than 400 RPM for 5 seconds.
* The ignition voltage is 8.6 volts or greater.
P0669
* No ISS DTCs P0716 or P0717.
* No OSS DTCs P0722 or P0723.
* The transmission output shaft speed is 200 RPM or greater for 200 seconds or more.
* The engine speed is greater than 400 RPM for 5 seconds.
* The ignition voltage is 8.6 volts or greater.
Conditions for Setting the DTC
P0667
* The difference between the transmission fluid temperature (TFT) and TCM substrate temperature is greater than 20-50掳C (36-90掳F),
depending on the average of the TFT, TCM substrate and TCM power up temperatures.
* The difference between the TCM power up temperature and TCM substrate temperature is greater than 8-10掳C (14-18掳F) depending on the
average of the TFT, TCM substrate and TCM power up temperatures.
* The above conditions have to be met for 5 minutes within a 6 minute period.
P0668
The TCM temperature is less than -249掳C (-416掳F) or less for 1 minute.
P0669
The TCM temperature is -249掳C (-416掳F) or greater for 1 minute.
Action Taken When the DTC Sets
* DTCs P0667, P0668, and P0669 are Type B DTCs.
* The TCM defaults the TCM substrate temperature to the TCM power up temperature.
Conditions for Clearing the DTC
Wednesday, September 29, 2021
Which is better Honda or Acura?
What's the world's rarest car?
2010 Cadillac Truck SRX AWD V6-3.0L Page 1822
2010 Cadillac Truck SRX AWD V6-3.0L Page 1822
DTC P0966
- Pressure Control Solenoid Valve 1 Control Circuit Low Voltage
DTC P0967
- Pressure Control Solenoid Valve 1 Control Circuit High Voltage
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The shift control solenoid (SLC1) is installed on the front valve body. The solenoid linearly control hydraulic pressure in response to signals output
from the transmission control module TCM. Through this, the SLC1 controls operating hydraulic pressure to the clutch 1 for smooth shifting.
According to each shift control solenoid assembly, the transmission shifts from 1st gear into 6th gear and vice versa. As a fail-safe function, if any
shift control solenoid assembly abnormality occurs, the TCM will disable the current to the solenoids.
Conditions for Running the DTC
P0778
* The ignition voltage is between 10.2-15.5 V.
* The engine speed is greater than 400 RPM for 2 s.
* The transmission is not in emergency mode.
* Driving in D range.
* TCM communication is normal.
* DTCs P0966 and P0967 are not set.
P0965
* The ignition voltage is between 10.2-15.5 V.
* The engine speed is greater than 400 RPM for 2 s.
* The transmission is not in emergency mode.
* Driving in D range.
* TCM communication is normal.
* The automatic transmission fluid temperature is more than 20掳C (68掳F).
* SLC1 current is more than 0.85 A.
* SLC1 target current is not changed.
P0966
* The ignition voltage is between 10.2-15.5 V.
* The engine speed is greater than 400 RPM for 2 s.
* The transmission is not in emergency mode.
* Driving in D range.
* TCM communication is normal.
* DTC P0967 is not set.
P0967
* The ignition voltage is between 10.2-15.5 V.
* The engine speed is greater than 400 RPM for 2 s.
* The transmission is not in emergency mode.
* Driving in D range.
* TCM communication is normal.
* DTC P0966 is not set.
Conditions for Setting the DTC
2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 3179
YES
The measurement value is OK.Possible cause and remedy
- Inspect connector 1 at control unit N80 (Steering column module) for damage, correct connection, loose contact and corrosion and repair, if
necessary.
End of test
NO
The measurement value is not OK.Possible cause and remedy
- Plug connection at control unit N80 (Steering column module)
- Line between component N80 (Steering column module) and component W12 (Ground, center console)
- Line between component N80 (Steering column module) and component F34f33 (Fuse 33)
End of test
1.3.2.1.7.4. Engine compartment CAN test
1.3.2.1.7.4. No further information available.
1.3.2.1.8. Check power supply at control unit N71 (Headlamp range adjustment control module).
If the fault code is not current, it may be deleted. In this case, the battery voltage was too low over an extended period.Charge the battery, if
necessary.Question:Is there a current undervoltage fault is several control modules?Note:This fault could result in consequential faults. You should
therefore process this fault first and then erase the fault memory.
YES
Possible cause and remedy
- Battery voltage too low.Test battery.Charge battery, replace if necessary.
- If fault occurs again:Check alternator.Communication with ECU required
- The quiescent current is too high.Test quiescent current.
NO
Figure legend 1:N71 (Headlamp range adjustment control module)Figure legend 2:N10/1 (Front SAM control unit with fuse and relay module)Test
prerequisite
- The relevant actual value is not okay.
- Battery voltage is OK.
- Fuse N10/1f51 (Fuse 51) is OK.
Popular Posts
-
Love For Cars The 2008 model may not look too different to the previous Accord, but under the surface, it is indeed all-new. The styling isn...
-
Vehicle: All Technical Service Bulletins Diesel Engine - Crackling/Ticking Noise At Idle Engine makes intermittent knocking noise, ticking...
-
P179A77 The redundancy system for DIRECT SELECT has a malfunction. The commanded position cannot be reached. Possible cause: A80 (Inte...
-
$102.25 End Date: Sunday Jul-28-2019 13:37:55 PDT Buy It Now for only: $102.25 Buy It Now | Add to watch list
-
$75.97 End Date: Sunday Jul-7-2019 11:44:55 PDT Buy It Now for only: $75.97 Buy It Now | Add to watch list
-
Bendix TitaniuMetallic2 Brake Pads are completely reformulated with TitaniuMetallic2 blue coating and is more effective during...
-
P0108 B28 (Pressure sensor) : Short circuit to positive or open circuit (P0108) Possible cause: B28 (Pressure sensor) Affected functi...
-
The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DI...
-
As of the latest 2025-2026 Tesla lineup, the cheapest Tesla you can buy new is the **Tesla **Model 3 Standard trim — an entry-level versi...
-
You don't need a supercar to have cool doors. There’s far more to a supercar than something as superficial as a cool pair of doors. But,...
Popular Posts
-
P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 A...
-
P2505 Relay 'Circuit 87' ( Engine ) (P2505) Possible cause: N3/10 (MESFI [ME] control unit) K40/4kK (Engine electronics an...
-
C426 Start enable 'Drive authorization system' not issued. Possible cause: Engine management Affected functions: ...
-
Misfiring of cylinder 4 : Damages TWC (P0304) Misfiring of cylinder 4 : Damages TWC (P0304) Possible cause: Combustion misfirings Aff...
-
Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Ch...
-
2010 Mercedes Benz Truck GL 350 BLUETEC (164.825) V6-3.0L DSL Turbo (642.820) Vehicle: All Technical Service Bulletins COMAND(R) - 'Dr...
-
2010 Mercedes Benz C 63 AMG Sedan (204.077) V8-6.3L (156.985) Vehicle: Customer Interest ABS/TCS - ABS Lamp ON/Codes 5603/5410 Set Y...
-
D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil ...
-
P179A77 The redundancy system for DIRECT SELECT has a malfunction. The commanded position cannot be reached. Possible cause: A80 (Inte...
-
P0108 B28 (Pressure sensor) : Short circuit to positive or open circuit (P0108) Possible cause: B28 (Pressure sensor) Affected functi...
Popular Posts
-
P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 A...
-
D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil ...
-
Vehicle: All Technical Service Bulletins Diesel Engine - Crackling/Ticking Noise At Idle Engine makes intermittent knocking noise, ticking...
-
Okay, so I need to figure out the financial results for Tesla's second quarter of 2025 based on the information provided. Let me start...
-
Mercedes-Benz Mercedes Benz OEM Parts Mercedes Benz OE Replacement Parts Technical Service Bulletin # LI83-30_P-05363...
-
P179A77 The redundancy system for DIRECT SELECT has a malfunction. The commanded position cannot be reached. Possible cause: A80 (Inte...
-
Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Ch...