2010 Cadillac Truck SRX FWD V6-3.0L Page 1210

2010 Cadillac Truck SRX FWD V6-3.0L Page 1210

Circuit/System Description

The heated oxygen sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding

air with the oxygen content of the exhaust stream. When the engine is started, the control module operates in an Open Loop mode, ignoring the

HO2S signal voltage while calculating the air-to-fuel ratio. While the engine runs, the HO2S heats up and begins to generate a voltage within a

range of 0-1,275 mV. Once sufficient HO2S voltage fluctuation is observed by the control module, Closed Loop is entered. The control module

uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases toward 1,000 mV indicates a rich fuel mixture. An HO2S

voltage that decreases toward 0 mV indicates a lean fuel mixture.

The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed

Loop earlier and the control module to calculate the air-to-fuel ratio sooner.

Conditions for Running the DTC

P0133, P0153, P1133, or P1153

* DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128,

P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516,

P2101, P2119, P2135, P2176 are not set.

* The engine coolant temperature (ECT) is greater than 71掳C (159掳F).

* The intake air temperature (IAT) is warmer than -40掳C (-40掳F)

* The ignition 1 voltage is between 10-32 V.

* The fuel level is greater than 10 %.

* The engine run time is greater than 60 s.

* The engine speed is between 1,000-3,000 RPM.

* The barometric (BARO) pressure is greater than 70 kPa.

* The mass airflow (MAF) is between 15-55 g/s.

* The fuel system is in Closed Loop.

* The throttle position (TP) is greater than 5 %.

* The DTCs run once per drive cycle when the above conditions are met.

P013A P013C, P013E, or P014A

* Before the ECM can report DTC P013A, or P013C failed, DTCs P013E, P014A, P2270, and P2272 must run and pass.

* Before the ECM can report DTC P013E, or P014A failed, DTCs P2270 and P2272 must run and pass.

* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,

P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,

P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are

not set.

* The ignition 1 voltage is between 10-32 V.

* The learned heater resistance is valid.

* The fuel level is greater than 10 %.

* The engine run time is equal to or greater than 5 min.

* The accelerator pedal (APP) is steady.