2010 Cadillac Truck SRX FWD V6-3.0L Page 1068

2010 Cadillac Truck SRX FWD V6-3.0L Page 1068

1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.

2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal D and ground.

瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests

normal and the B52 HO2S heater circuit fuse is open, test all components connected to the fuse and replace as necessary.

3. Ignition ON, observe the appropriate scan tool HO2S Heater Control Open Circuit Test Status parameter. The parameter should display

Malfunction.

瀚慖f not the specified value, test the heater control circuit terminal E for a short to ground, or for a short to voltage. If the circuit tests

normal, replace the K20 ECM.

4. Connect a 3 A fused jumper wire between the heater control circuit terminal E and ground. Observe the appropriate scan tool HO2S Heater

Control Circuit Low Voltage Test Status parameter. The parameter should transition from OK to Malfunction.

瀚慖f not the specified value, test the heater control circuit terminal E for an open/high resistance. If the circuit tests normal, replace the K20

ECM.

Note:

* Less than 10 ohm of additional resistance on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a

circuit, the driver will remain ON and the scan tool HO2S High Voltage Test Status parameter will display OK.

* Performing this test may set additional DTCs.

5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal E and the ignition voltage circuit terminal D.

6. Engine idling, observe the appropriate HO2S Control Circuit High Voltage Test Status parameter. The parameter should transition from Not

Run to Malfunction.

瀚慖f not the specified value, test the control circuit and the ignition voltage circuit for high resistance. If the circuits test normal, replace the

K20 ECM.

7. If all circuits test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 1)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 2)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 1)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P054B

DTC P052B, P052D, P054B, or P054D

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P052B

- Cold Start Intake Camshaft Position System Performance Bank 1 - Retarded

DTC P052D

- Cold Start Intake Camshaft Position System Performance Bank 2 - Retarded