Wednesday, March 23, 2022

Disclaimer2010 Cadillac Truck Escalade EXT AWD V8-6.2L Technical Service Bulletin # 11273 Date: 120920

Disclaimer2010 Cadillac Truck Escalade EXT AWD V8-6.2L Technical Service Bulletin # 11273 Date: 120920



Campaign - Throttle Position Sensor Replacement



SPECIAL COVERAGE



Bulletin No.: 11273



Date: September 20, 2012



Subject: -- 11273 Special Coverage Adjustment Throttle Position Sensor Replacement



Models:



2008-2010 Cadillac Escalade, Escalade ESV, Escalade EXT



2008-2009 Chevrolet TrailBlazer



2008-2010 Chevrolet Avalanche, Express, Silverado, Suburban, Tahoe



2009-2010 Chevrolet Colorado



2008-2009 GMC Envoy



2008-2010 GMC Savana, Sierra, Yukon, Yukon XL



2009-2010 GMC Canyon



2008-2009 HUMMER H2



2008-2010 HUMMER H3



2009-2010 HUMMER H3T



Equipped with V8 Engine (LFA, LY2, L20, LMG, LC9, LH6, LMF, LH8, LH9, L76, LS2, LY5, LY6, L92, L96, LZ1, L94, L9H)



Customers involved in this Special Coverage will be notified in phases. The first phase will include customers with 2008 model year vehicles.



Condition



On some 2008-2009 Chevrolet TrailBlazer; GMC Envoy; HUMMER H2; 2008-2010 Cadillac Escalade, Escalade ESV, Escalade EXT; Chevrolet



Avalanche, Express, Silverado, Suburban, Tahoe; GMC Savana, Sierra, Yukon, Yukon XL; HUMMER H3; 2009-2010 Chevrolet Colorado; GMC



Canyon; and HUMMER H3T vehicles, equipped with a V8 engine, the throttle position sensor may cause the engine to run rough and cause the



malfunction indicator lamp and/or an Engine Reduced Power message to illuminate. If this occurs, it could result in reduced engine power.



Special Coverage Adjustment



This special coverage covers the condition described above for a period of 10 years or 120,000 miles (193,000 km), whichever occurs first, from



the date the vehicle was originally placed in service, regardless of ownership.



Dealers are to replace the throttle position sensor and reprogram the Engine Control Module. The repairs will be made at no charge to the customer.



For vehicles covered by Vehicle Service Contracts, all eligible claims with repair orders on or after September 21, 2012, are covered by this special



coverage and must be submitted using the labor operation codes provided with this bulletin. Claims with repair orders prior to September 21, 2012,



must be submitted to the Service Contract provider.



Vehicles Involved



All involved vehicles are identified by Vehicle Identification Number on the Applicable Warranties section in GM Global Warranty Management



2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 30



system. Dealership service personnel should always check this site to confirm vehicle involvement prior to beginning any required inspections



and/or repairs. It is important to routinely use this tool to verify eligibility because not all similar vehicles may be involved regardless of description



or option content.



Parts Information



Parts required to complete this special coverage are to be obtained from General Motors Customer Care and Aftersales (GMCC&A).



Customer Reimbursement - For US



Customer requests for reimbursement of previously paid repairs to correct the condition described in this bulletin are to be submitted to the dealer



by December 31, 2013, unless otherwise specified by state law. If this is not convenient for the customer, they may mail the completed Customer



Reimbursement Request Form and all required documents to the GM Customer Assistance Center. Repairs must have occurred within the 10 years



of the date the vehicle was originally placed in service, or 120,000 miles, whichever occurs first.



All reasonable and customary costs to correct the condition described in this bulletin should be considered for reimbursement. Any



questions or concerns should be reviewed with your District Service Manager - Aftersales prior to processing the request.



When a customer requests reimbursement, they must provide the following:



- A completed Customer Reimbursement Request Form. This form is mailed to the customer or can be obtained through GM GlobalConnect.



- The name and address of the person who paid for the repair.



- Paid receipt confirming the amount of the repair expense, a description of the repair, and the person or entity performing the repair.



Important



GM requires dealers to approve or deny a reimbursement request within 30 days of receipt. If a reimbursement request is approved, the



dealer should immediately issue a check to the customer and submit an appropriate warranty transaction for the incurred expense. If a



reimbursement request is denied, the dealer MUST provide the customer with a clear and concise explanation, in writing, as to why the request



was denied. The bottom portion of the Customer Reimbursement Request Form may be used for this purpose. If the denial was due to missing



documents, the customer can resubmit the request when the missing documents are obtained, as long as it is still within the allowed reimbursement



period.



Warranty transactions for customer reimbursement of previously paid repairs are to be submitted as required by GM Global Warranty Management.



Additional information can also be found in Warranty Administration Bulletin 11-00-89-004.



Customer Reimbursement - For Canada and Export



Customer requests for reimbursement of previously paid repairs to correct the condition described in this bulletin are to be submitted to the dealer



prior to or by December 31, 2013. Repairs must have occurred within the 10 years of the date the vehicle was originally placed in service, or



193,000 kilometers, whichever occurs first.



When a customer requests reimbursement, they must provide the following:



- Proof of ownership at time of repair.



- Original paid receipt confirming the amount of unreimbursed repair expense(s) (including Service Contract deductibles), a description of the



repair, and the person or entity performing the repair.



If the work was done by someone other than a GM dealership, the amount of reimbursement will be limited to the amount that the repair would



have cost GM to have it completed by a GM dealership.



Courtesy Transportation - For US and Canada



The General Motors Courtesy Transportation program is intended to minimize customer inconvenience when a vehicle requires a repair that is



covered by the New Vehicle Limited Warranties. The availability of courtesy transportation to customers whose vehicles are within the warranty



coverage period and involved in a product program is very important in maintaining customer satisfaction. Dealers are to ensure that these



customers understand that shuttle service or some other form of courtesy transportation is available and will be provided at no charge. Dealers



should refer to the General Motors Service Policies and Procedures Manual for Courtesy Transportation guidelines.



Warranty Transaction Information



Submit a transaction using the table below.



2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 31



* The amount identified in "Net Item" should represent the dollar amount reimbursed to the customer.



Customer Notification



General Motors will notify customers of this special coverage on their vehicles (see copy of typical customer letter included with this bulletin -



actual divisional letter may vary slightly).



Disclaimer



Service Procedure



Service Procedure



Caution



Handle the electronic throttle control components carefully. Use cleanliness in order to prevent damage. Do not drop the electronic throttle control



components. Do not roughly handle the electronic throttle control components. Do not immerse the electronic throttle control components in



cleaning solvents of any type.



Warning



Approved safety glasses and gloves should be worn when performing this procedure to reduce the chance of personal injury.



1. With a scan tool, verify that DTC P2135 is set as Current or in History.



- If DTC P2135 is set as Current or in History, proceed to Step 2 and perform the service procedure in this bulletin.



- If DTC P2135 is NOT set as Current or in History, refer to Diagnostic Trouble Code (DTC) List - Vehicle or Symptoms - Engine



Controls in SI. Determine cause of condition. Repairs, if required, are NOT covered by the labor operation codes in this bulletin. Bill



repair under warranty, goodwill assistance or customer pay.



2. Turn OFF the ignition.



3. Open the hood.



Note



If at any time during this procedure the throttle body is dropped, abort this procedure and REPLACE it with a new throttle body assembly.



4. Remove the throttle body and discard the throttle body gasket. Refer to Throttle Body Assembly Replacement in SI.



5. Remove any loose debris and dirt from the throttle body assembly and the TP sensor cover. Inspect the throttle body for damage.



Caution



Do not use any solvent that contains Methyl Ethyl Ketone (MEK). This solvent may damage fuel system components.



6. Clean the throttle body bore and the throttle plate using a clean shop towel with GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N



993026), or AC-Delco Upper Engine and Fuel Injector Cleaner, P/N X66-P, or an equivalent product.



2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 32



Note



DO NOT mount the throttle body in a vise. The throttle body can be set on the top of a soft protected workbench area.



7. Hold the throttle body with your hand, so that the throttle position (TP) sensor cover is facing upward as shown.



8. Secure a rubber band around the throttle body and TP sensor cover as shown.



9. Turn over the throttle body and use a flathead screwdriver to remove the two clips (1, 2) as shown. Discard the clips.



Caution



Do NOT pry on the machined sealing surface of the throttle body inlet duct.



10. Turn over the throttle body and use a flathead screwdriver to remove the four remaining clips from the TP sensor cover. Discard the clips.



11. Hold the throttle body with your hand, so that the TP sensor cover is facing upward. Grasp the TP sensor cover and carefully lift it up and



separate it from the throttle body.



2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 33



Note



DO NOT allow the intermediate gear to fall out.



12. Maintain the throttle body in an upward position. Use your thumb to maintain contact with the intermediate gear.



If the intermediate gear falls out and impacts a hard workbench surface or the floor, abort this procedure and REPLACE with a new throttle



body assembly.



13. Verify that the TP sensor cover gasket HAS REMAINED in the TP sensor cover as shown. Ensure that the gasket is accounted for and



remains with the old TP sensor cover.



Note



If one or both of the TP sensor cover female throttle actuator motor terminals HAVE BEEN retained on the throttle actuator motor male



terminals (2), remove and discard those female terminals.



14. Observe the TP sensor cover for missing female throttle actuator motor terminals (1). Verify that the female throttle actuator motor terminals



HAVE REMAINED in the TP sensor cover and HAVE NOT been retained on the throttle actuator motor male terminals (2). Discard the old



TP sensor cover, gasket and terminals.



15. Remove the new TP sensor cover from the protective shipping wrapper.



2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 34



Note



If the TP sensor drive slot orientation is not aligned as shown, use a small flathead screwdriver to gently rotate the TP sensor drive slot



clockwise to the wide open throttle (WOT) position as shown.



16. Place the TP sensor cover in the position as shown. Confirm the TP sensor drive slot orientation is aligned in the TP sensor cover as shown.



17. Verify that the TP sensor cover gasket is secure and properly positioned.



Note



The three TP sensor cover alignment tabs are highlighted in white for identification purposes only.



18. Verify that all three of the TP sensor cover alignment tabs are present and are not damaged.



19. Grasp and hold the throttle body in the previously hand held upward position. Lightly depress the intermediate gear to verify that it is fully



seated and the gears are engaged.



2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 35



20. Rotate the throttle body plate to the WOT position (1).



21. Position and install the TP sensor cover to the throttle body. Hold the TP sensor cover in position. If necessary for ease of the clip



installation, secure a rubber band around the throttle body and TP sensor cover.



22. Install the first new TP sensor cover clip (1) in the position shown.



23. Install the remaining new TP sensor cover clips in the sequence shown.



24. Install a NEW throttle body gasket to the intake manifold.



25. Install the throttle body, bolts and nuts. DO NOT tighten the fasteners yet.



26. Connect the electrical connector to the throttle body.



27. Turn ON the ignition. Clear the DTC with a scan tool.



28. Observe the scan tool TP Sensor 1 and 2 Agree/Disagree parameter while slowly depressing the accelerator pedal to WOT and then slowly



returning the pedal to closed throttle. Repeat the procedure several times. Rapidly depress the accelerator pedal from the rest position to the



wide open throttle position (WOT) and release pedal. Repeat the procedure several times. The TP Sensor 1 and 2 Agree/Disagree parameter



should display Agree.



- If TP Sensor 1 and 2 Agree/Disagree parameter displays Agree, proceed to Step 29.



2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 36



- If TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.



29. Observe the engine control module (ECM) module DTC information. Are DTC P1516, P2101 and/or P2176 set?



- If DTC P1516, P2101 and/or P2176 are set, replace the throttle body.



- If DTC P1516, P2101 and/or P2176 are not set, proceed to Step 30.



30. Tighten the throttle body fasteners.



Tighten:



Tighten the fasteners to 10 Nm (89 lb in).



31. Install any remaining components that were removed during this procedure.



32. Verify the battery voltage is more than 12 volts but less than 16 volts before proceeding with ECM reprogramming.



33. During reprogramming, the battery voltage must be maintained within the proper range of 12-15 volts. Connect the approved Midtronics(R)



PSC 550 Battery Maintainer (SPS Programming Support Tool EL-49642) to the vehicle.



If the above recommended tool is not available, DO NOT connect a battery charger to the vehicle. Connect a fully charged 12V jumper or



booster pack that is disconnected from the AC voltage supply.



34. Use a Tech 2(R) or a multiple diagnostic interface (MDI) module for reprogramming. Ensure that either device is updated with the latest



available software version before performing the reprogramming event.



35. Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB. Refer to the SPS



procedures in SI.



36. Perform the Throttle Learn Reset Procedure. Refer to Throttle/Idle Learn > Throttle Learn > Reset Procedure in SI.



Owner Letter



Owner Letter



Dear General Motors Customer:



As the owner of a 2008, 2009, or 2010 GM vehicle, your satisfaction with our product is very important to us.



This letter is intended to make you aware that some 2008-2009 Chevrolet TrailBlazer; GMC Envoy; HUMMER H2; 2008-2010 Cadillac Escalade,



Escalade ESV, Escalade EXT; Chevrolet Avalanche, Express, Silverado, Suburban, Tahoe; GMC Savana, Sierra, Yukon, Yukon XL; HUMMER



H3; 2009-2010 Chevrolet Colorado; GMC Canyon; and HUMMER H3T vehicles, equipped with a V8 engine, may have a condition where the



throttle position sensor may cause the engine to run rough and cause the malfunction indicator lamp and/or an Engine Reduced Power message to



illuminate. If this occurs, it could result in reduced engine power.



Do not take your vehicle to your GM dealer as a result of this letter unless you believe that your vehicle has the condition as described above.



What We Have Done: General Motors is providing owners with additional protection for the condition described above. If this condition occurs



on your 2008-2009 Chevrolet TrailBlazer; GMC Envoy; HUMMER H2; 2008-2010 Cadillac Escalade, Escalade ESV, Escalade EXT; Chevrolet



Avalanche, Express, Silverado, Suburban, Tahoe; GMC Savana, Sierra, Yukon, Yukon XL; HUMMER H3; 2009-2010 Chevrolet Colorado; GMC



Canyon; or HUMMER H3T vehicle, equipped with a V8 engine, within 10 years of the date your vehicle was originally placed in service or



120,000 miles (193,000 km), whichever occurs first, the condition will be repaired for you at no charge. Diagnosis or repair for conditions other



than the condition described above is not covered under this special coverage program.



What You Should Do: If you believe that your vehicle has the condition described above, repairs and adjustments qualifying under this special



coverage must be performed by a General Motors dealer. You may want to contact your GM dealer to find out how long they will need to have



your vehicle so that you may schedule the appointment at a time that is convenient for you. This will also allow your dealer to order parts if they are



not already in stock. Keep this letter with your other important glove box literature for future reference.



Reimbursement: If you have paid for repairs for the condition described in this letter, please complete the enclosed form and present it to your



dealer with all required documents. Working with your dealer will expedite your request, however, if this is not convenient, you may mail the



completed form and all required documents to Reimbursement Department, PO Box 33170, Detroit, MI 48232-5170. The completed form and



required documents must be presented to your dealer or received by the Reimbursement Department by December 31, 2013, unless state law



specifies a longer reimbursement period.



If you have any questions or need any assistance, just contact your dealer or the appropriate Customer Assistance Center at the number listed



below.



2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 37



We are sorry for any inconvenience you may experience; however we have taken this action in the interest of your continued satisfaction with our



products.



Jim Moloney



General Director,



Customer and Relationship Services

No comments:

Post a Comment