2010 Cadillac Truck SRX FWD V6-3.0L Page 935

2010 Cadillac Truck SRX FWD V6-3.0L Page 935

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate B52 HO2S harness connector.

2. Ignition ON, observe the appropriate scan tool HO2S voltage parameter. The parameter should display 1.27 V.

瀚慖f less than the specified range, test the high and low signal circuits for a short to ground. If both signal circuit test normal, replace the

K20 ECM.

3. Ignition ON, test for 2.5-3.0 V between the high signal circuit terminal B and ground.

瀚慖f less than the specified range, test the high signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

瀚慖f greater than the specified range, test the high signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition OFF, connect a 3 A fused jumper wire between the high signal circuit terminal B and the low signal circuit terminal A.

Note: The low signal circuit is tied to a pull-up circuit within the ECM. A voltage of 0.90-1.10 V on the low signal circuit is normal.

5. Ignition ON, verify the scan tool HO2S parameter displays 0.0 V.

瀚慖f greater than the specified range, test the low signal circuit for an open/high resistance or for a short to voltage. If the circuit tests

normal, replace the K20 ECM.

6. If all circuits test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 1)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 2)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 1)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P2A04

DTC P0131, P0132, P0137, P0138, P0151, P0152, P0157, P0158, P2A00, P2A01, P2A03, or P2A04 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0131

- HO2S Circuit Low Voltage Bank 1 Sensor 1

DTC P0132

- HO2S Circuit High Voltage Bank 1 Sensor 1

DTC P0137

- HO2S Circuit Low Voltage Bank 1 Sensor 2