Wednesday, December 8, 2021

2010 Cadillac Truck SRX FWD V6-3.0L Page 1009

2010 Cadillac Truck SRX FWD V6-3.0L Page 1009



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0016



- Crankshaft Position - Intake Camshaft Position Not Plausible Bank 1



DTC P0017



- Crankshaft Position - Exhaust Camshaft Position Not Plausible Bank 1



DTC P0018



- Crankshaft Position - Intake Camshaft Position Not Plausible Bank 2



DTC P0019



- Crankshaft Position - Exhaust Camshaft Position Not Plausible Bank 2



Circuit/System Description



The engine control module (ECM) uses the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor pulses to monitor the



correlation between the crankshaft and the camshaft position. An improper relative position can be caused by either engine timing or improper



indexing of the camshaft drive chain.



Conditions for Running the DTC



* DTC P0335, P0336, P0338, P0340, P0341, P0345, P0346, P0365, P0366, P0390, P0391, P0641, and P0651 are not set.



* The engine is operating.



* The crankshaft and camshaft position signals are synchronized.



* The camshaft position actuator is in the parked position.



* DTC P0016, P0017, P0018, and P0019 run continuously once the above conditions are met.



Conditions for Setting the DTC



DTC P0016, P0017, P0018, or P0019



The ECM detects that one camshaft is mis-aligned with the crankshaft. The ECM detects one of the following conditions:



* Bank 1 intake camshaft is greater than 9 degrees retarded or 12 degrees advanced in relationship to the crankshaft.



* Bank 1 exhaust camshaft is greater than 10 degrees retarded or 13 degrees advanced in relationship to the crankshaft.



* Bank 2 intake camshaft is greater than 11 degrees retarded or 13 degrees advanced in relationship to the crankshaft.



* Bank 2 exhaust camshaft is greater than 9 degrees retarded or 13 degrees advanced in relationship to the crankshaft.



DTC P0016 and P0017



The ECM detects that both camshafts on bank 1 are mis-aligned with the crankshaft. The ECM detects the following conditions:



* Bank 1 intake camshaft is greater than 6 degrees retarded or 9 degrees advanced in relationship to the crankshaft.



* Bank 1 exhaust camshaft is greater than 6 degrees retarded or 9 degrees advanced in relationship to the crankshaft.



DTC P0018 and P0019



The ECM detects that both camshafts on bank 2 are mis-aligned with the crankshaft. The ECM detects the following conditions:



* Bank 2 intake camshaft is greater than 6 degrees retarded or 9 degrees advanced in relationship to the crankshaft.



* Bank 2 exhaust camshaft is greater than 7 degrees retarded or 9 degrees advanced in relationship to the crankshaft.



DTC P0016, P0017, P0018, and P0019



The ECM detects that all 4 camshafts are mis-aligned with the crankshaft. The ECM detects the following conditions:



* Bank 1 intake camshaft is greater than 6 degrees retarded or 9 degrees advanced in relationship to the crankshaft.



* Bank 1 exhaust camshaft is greater than 6 degrees retarded or 9 degrees advanced in relationship to the crankshaft.



* Bank 2 intake camshaft is greater than 6 degrees retarded or 8 degrees advanced in relationship to the crankshaft.



* Bank 2 exhaust camshaft is greater than 7 degrees retarded or 9 degrees advanced in relationship to the crankshaft.



Action Taken When the DTC Sets



DTCs P0016, P0017, P0018, and P0019 are type B DTCs.

No comments:

Post a Comment