Saturday, November 20, 2021

2010 Cadillac Truck SRX FWD V6-3.0L Page 1212

2010 Cadillac Truck SRX FWD V6-3.0L Page 1212



* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical



Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.



瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code



Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).



2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Verify none of the following conditions exist:



* Lean or rich fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air



Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel



Delivery and Air Induction/Fuel Injector/Testing and Inspection).



* Water intrusion in the B52 HO2S harness connector



* Low or high fuel system pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air



Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:



Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel



System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel



System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air



Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).



* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery



and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel



Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component



Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)).



* Fuel saturation of the evaporative emission (EVAP) canister



* Exhaust leaks near the B52 HO2S



* Engine vacuum leaks



* Engine oil consumption-Refer to Oil Consumption Diagnosis (See: Engine, Cooling and Exhaust/Engine/Testing and



Inspection/Component Tests and General Diagnostics/Oil Consumption Diagnosis).



* Engine coolant consumption-Refer to Loss of Coolant (See: Engine, Cooling and Exhaust/Cooling System/Testing and



Inspection/Symptom Related Diagnostic Procedures/Loss of Coolant).



瀚慖f you find any of the above conditions, repair as necessary.



2. If all conditions test normal, test or replace the appropriate B52 HO2S.



Repair Instructions



Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control



Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen



Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 1)



* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen



Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 2)



* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen



Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 1)



* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen



Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

No comments:

Post a Comment