2010 Cadillac Truck SRX AWD V6-3.0L Page 2145

2010 Cadillac Truck SRX AWD V6-3.0L Page 2145

Circuit/System Testing

Command the TCC Solenoid Valve increase and decrease with a scan tool. The value should rise from 0.1-1.1 A and return to 0.1 A.

If the value does not change, turn ignition OFF, remove the K71 Transmission Control Module. Connect a test lamp between the low reference

circuit terminal 4 X2 at the K71 Transmission Control Module and the voltage supply component circuit terminal 9 X2 at the K71 Transmission

Control Module. Command the TCC Solenoid Valve increase and decrease with a scan tool. The test lamp has to illuminate brighter with increasing

current.

If the test lamp always illuminates or always does not illuminate, replace the K71 Transmission Control Module.

Component Testing

Static Test

1. Ignition OFF, remove the K71 Transmission Control Module.

2. Test for 5-5.6 ohm at 20掳C (68掳F) between the low reference circuit terminal 4 X2 and the voltage supply circuit terminal 9 X2.

瀚慖f less than the specified range, test the wiring harness for internal short. If the circuit test normal, replace the Q27D Pressure Control

Solenoid Valve 4.

3. Test for infinite resistance between each terminal and the low reference circuit terminal 4 X2 and also to the voltage supply circuit terminal 9

X2.

瀚慖f less than the specified range, replace the wiring harness.

4. If all circuit test normal, perform the control solenoid valve inspection. Refer to Control Solenoid Valve Inspection (M36 and MXE) (See:

Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/AF40-6 -

Automatic Transmission).

瀚慖f the inspection test normal, replace the control valve body.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Control valve body replacement-Refer to Control Valve Body Replacement (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Valve Body/Service and Repair/AF40-6 - Automatic Transmission/Control Valve Body Replacement) for

replacement, setup, and programming.

* TCM-Refer to Control Module References (See: Testing and Inspection/Programming and Relearning) for replacement, setup, and

programming.

* Perform the Transmission Adaptive Functions (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/AF40-6 - Automatic Transmission/Transmission Adaptive Functions).

* Wiring harness-Refer to Automatic Transmission Wiring Harness Replacement (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Wiring Harness/Service and Repair) for replacement.

6T70/6T75 - Automatic Transmission

DTC P2762, P2763, or P2764

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P2762

- Torque Converter Clutch (TCC) Pressure Control Solenoid System Performance

DTC P2763

- Torque Converter Clutch (TCC) Pressure Control Solenoid Control Circuit High Voltage

DTC P2764

- Torque Converter Clutch (TCC) Pressure Control Solenoid Control Circuit Low Voltage