Wednesday, June 2, 2021

2010 Cadillac Truck SRX AWD V6-3.0L Page 2150

2010 Cadillac Truck SRX AWD V6-3.0L Page 2150



* The TCM turns OFF all solenoids.



* The TCM allows the vehicle to operate only in second gear and "R" range after a stop.



Conditions for Clearing the DTC



P2759, P2762



* DTCs P2759 and P2762 are Type B DTCs.



* The TCM detects the error current less than 50 mA for 2.75 ms.



P2763, P2764



* DTCs P2763 and P2764 are Type B DTCs.



* The current consumption of the SLU control circuit is 0.1-1.1 A for 500 ms.



Diagnostic Aids



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure



a 3掳C (5掳F) increase in TCM substrate temperature. This will place the TCM in the optimal condition to test solenoid electrical DTCs.



Reference Information



Schematic Reference



Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams/Electrical



Diagrams)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



Description and Operation



Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and



Operation/AF40-6 - Automatic Transmission/Transmission Component and System Description)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ensure the transmission fluid temperature is between 50-80掳C (122-176掳F).



2. Operate the vehicle in 2nd gear long enough to ensure at least a 3掳C (5掳F) rise in transmission fluid temperature, then operate the vehicle in



Park for 5 s.



3. Observe the scan tool data TCC Pressure Control Solenoid Valve Current parameter. The reading should be between 0.1-1.1 A.



Circuit/System Testing



Command the TCC Solenoid Valve increase and decrease with a scan tool. The value should rise from 0.1-1.1 A and return to 0.1 A.



If the value does not change, turn ignition OFF, remove the K71 Transmission Control Module. Connect a test lamp between the low reference



circuit terminal 4 X2 at the K71 Transmission Control Module and the voltage supply component circuit terminal 9 X2 at the K71 Transmission



Control Module. Command the TCC Solenoid Valve increase and decrease with a scan tool. The test lamp has to illuminate brighter with increasing



current.



If the test lamp always illuminates or always does not illuminate, replace the K71 Transmission Control Module.



Component Testing



Static Test



1. Ignition OFF, remove the K71 Transmission Control Module.

No comments:

Post a Comment