2010 Cadillac Truck SRX AWD V6-3.0L Page 1815

2010 Cadillac Truck SRX AWD V6-3.0L Page 1815

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

DT-47825-20 Adapter Harness

Circuit/System Verification

1. Operate the vehicle in second gear long enough to ensure at least a 3掳C (5掳F) rise in TCM temperature, then operate the vehicle in Park for 5

seconds.

2. Operate the vehicle in drive range. Allow the transmission to shift through all forward gear ranges. Verify with a scan tool the following test

status parameters display OK:

* PC Sol. 2 Perf. Test Status

* PC Sol. 2 Ckt. High Voltage Test Status

* PC Sol. 2 Ckt. Low Voltage Test Status

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: You must perform the Circuit/System Verification first.

1. Ignition OFF, remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly

Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and

Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).

2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Control

Solenoid Valve and Transmission Control Module Assembly Inspection).

3. Place the control solenoid valve assembly on a clean work surface near the transmission assembly.

4. Connect DT-47825-20 - jumper harness between the vehicle wire harness electrical connector, and the control solenoid valve assembly

electrical connector.

5. Ignition ON, verify with a scan tool the following test status parameters display OK:

* PC Sol. 2 Perf. Test Status

* PC Sol. 2 Ckt. High Voltage Test Status

* PC Sol. 2 Ckt. Low Voltage Test Status

瀚慖f any test status parameter displays Fault or Malfunction, replace the control solenoid valve assembly.

Repair Instructions

Important:

* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and

Inspection/Programming and Relearning) following all transmission related repairs.

* Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See:

Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General

Diagnostics/6T70/6T75 - Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,

and programming

AF40-6 - Automatic Transmission