2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1988

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1988

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0300

- Engine Misfire Detected

DTC P0301

- Cylinder 1 Misfire Detected

DTC P0302

- Cylinder 2 Misfire Detected

DTC P0303

- Cylinder 3 Misfire Detected

DTC P0304

- Cylinder 4 Misfire Detected

DTC P0305

- Cylinder 5 Misfire Detected

DTC P0306

- Cylinder 6 Misfire Detected

DTC P0307

- Cylinder 7 Misfire Detected

DTC P0308

- Cylinder 8 Misfire Detected

Circuit/System Description

The engine control module (ECM) uses information from the crankshaft position (CKP) sensor in order to determine when an engine misfire is

occurring, and uses information from the camshaft position (CMP) sensor in order to determine which cylinder is misfiring. By monitoring

variations in the crankshaft rotation speed for each cylinder, the ECM is able to detect individual misfire events. If the ECM detects a misfire rate

sufficient to cause emission levels to exceed mandated standards, DTC P0300 sets. Under certain driving conditions, a misfire rate can be high

enough to cause the catalytic converter to overheat, possibly damaging the converter. The malfunction indicator lamp (MIL) will flash ON and OFF

when catalytic converter overheating conditions are present and DTC P0300 is set. DTCs P0301-P0308 corresponds to cylinders 1-8. If the ECM is

able to determine that a specific cylinder is misfiring, the DTC for that cylinder will also set.

Conditions for Running the DTC

* DTCs P0010, P0011, P0016, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0122, P0123,

P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and

P2176 are not set.

* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.

* Engine run time is more than 2 crankshaft revolutions.

* The engine speed is between 375-5,600 RPM.

* The ignition voltage is between 9-18 volts.

* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).

* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).

* The fuel level is more than 10 percent.

* The ECM is not in fuel shut-off, or decel fuel cut-off mode.

* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.

* An automatic transmission shift with a throttle position more than 95 percent is not occuring.

* The power management is not active.

* Excessive drive wheel slip is not detected.

* The power take-off (PTO) is disabled, where applicable.

* The cylinder deactivation is not in progress, where applicable.

* DTCs P0300-P0308 run continuously when the above conditions are met.

Conditions for Setting the DTC

DTC P0300

The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at

catalytic converter damaging levels.