2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2252

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2252

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Special Tools

J 24731 Tempil Stick

Circuit/System Verification

Ignition ON, observe the scan tool Trans. Fluid Temp. and the TCM temperature parameters. The readings should vary less than 10掳C (18掳F).

If within the specified range, test for a transmission overheat condition.

If greater than the specified range, replace the Q8 control solenoid valve assembly.

Component Testing

* Perform the Fluid Leak Diagnosis (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component

Tests and General Diagnostics/2ML70 - Automatic Transmission/Fluid Leak Diagnosis).

* Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing

and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Transmission Fluid Level and Condition Check)

procedure.

* Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component

Tests and General Diagnostics/2ML70 - Automatic Transmission/Line Pressure Check) procedure.

* Perform the Main Fluid Pump Pressure High or Low (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and

Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Main Fluid Pump Pressure High or Low) procedure.

* With a hand held infra red thermometer, or J 24731 test for the transmission cooler supply line thermostat for opening at 80掳C (176掳F). The

transmission cooler supply line temperature should be higher on the transmission side of the thermostat than the cooler side until 80掳C (176掳

F) is reached.

瀚慖f the thermostat tests stuck open or closed, replace the transmission cooler supply pipe assembly.

Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid

Valve and Transmission Control Module Assembly Inspection).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Transmission Fluid Cooler Pipe Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Fluid

Line/Hose/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Q8 control solenoid valve assembly

replacement, setup, and programming.

P0713

DTC P0711, P0712, or P0713

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System