2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2258
Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and
Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).
2. Connect the DT-47825-10 - jumper harness between the vehicle wire harness electrical connector, and the Q8 control solenoid valve
assembly electrical connector.
3. Ignition ON, test for 8.3-9.3 volts between the ISS/OSS voltage circuit terminal B on the Q8 control solenoid valve assembly and ground at
the transmission case.
瀚慖f not within the specified range, replace the control solenoid valve assembly.
4. Perform the Control Solenoid Valve and Transmission Control Module Assembly Input Shaft Speed/Output Shaft Speed Input Test (See:
Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General
Diagnostics/6L45/6L50/6L80/6L90 - Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Input
Shaft Speed/Output Shaft Speed Input Test).
5. Inspect the machined teeth on the 1-2-3-4 and 3-5 clutch housing outer surface for damage or misalignment. Repair or replace as necessary.
6. If all of the above test normal, replace the B14A/B14C ISS/OSS assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Perform the Input and Output Speed Sensor Replacement (See: Powertrain Management/Transmission Control Systems/Sensors and
Switches - Transmission and Drivetrain/Sensors and Switches - A/T/Transmission Speed Sensor/Service and Repair/6L45/6L50/6L80/6L90 -
Automatic Transmission).
* Control solenoid valve assembly - refer to Control Module References (See: Testing and Inspection/Programming and Relearning) for
replacement, setup, and programming.
* Perform the Control Solenoid Valve and Transmission Control Module Assembly Input Shaft Speed/Output Shaft Speed Input Test (See:
Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General
Diagnostics/6L45/6L50/6L80/6L90 - Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Input
Shaft Speed/Output Shaft Speed Input Test).
* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Programming and Relearning) following all transmission related repairs.
P0717
DTC P0716 or P0717
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0716
- Input Speed Sensor Performance
DTC P0717
- Input Speed Sensor Circuit Low Voltage
Diagnostic Fault Information
Typical Scan Tool Data
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Saturday, November 21, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2258
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment