2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2202
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information
Circuit/System Verification
1. Observe the scan tool 5 V reference 1 circuit status and the 5 V reference 2 circuit status parameters. Verify the parameters display OK.
2. Ignition ON, observe the DTC information with a scan tool. DTC P0641 or P0651 should not set on this ignition cycle.
3. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed
from the Freeze Frame/Failure Records data.
Circuit/System Testing
Note: Additional DTCs may set when disconnecting components.
1. Ignition OFF, disconnect the harness connector of all the sensors connected to the 5 V reference bus for the applicable DTC. Refer to
Circuit/System Description.
Note: A short to voltage on the signal circuit of certain components may cause this DTC to set.
2. Ignition ON, test for 4.8-5.2 V between one of the 5 V reference circuits and ground.
瀚慖f less than the specified range, test all of the 5 V reference circuits for a short to ground. If all circuits test normal, replace the K20 ECM.
瀚慖f greater than the specified range, test for a short to voltage on all of the 5 V reference circuits, or the signal circuit for each component
associated with the appropriate 5 V reference bus for a short to voltage. If all circuits test normal, replace the K20 ECM.
3. Connect each component associated with the appropriate 5 V reference bus, one at a time, while monitoring the voltage. The voltage should
not change more than 1 V.
瀚慖f the voltage display changes more than the specified range when a component is connected, replace the component.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Accelerator Pedal Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Accelerator Pedal Position
Sensor/Service and Repair)
* Camshaft Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Camshaft Position Sensor/Service
and Repair)
* Crankshaft Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Crankshaft Position
Sensor/Service and Repair)
* Engine Oil Pressure Sensor and/or Switch Replacement (See: Engine, Cooling and Exhaust/Engine/Engine Lubrication/Oil Pressure
Sensor/Service and Repair)
* Fuel Tank Pressure Sensor Replacement (1500 LWB - 117.3L (31 gal) Tank + E85) (See: Powertrain Management/Computers and Control
Systems/Fuel Tank Pressure Sensor/Service and Repair/Fuel Tank Pressure Sensor Replacement (1500 LWB - 117.3L (31 Gal) Tank + E85)
)Fuel Tank Pressure Sensor Replacement (2500 Series) (See: Powertrain Management/Computers and Control Systems/Fuel Tank Pressure
Sensor/Service and Repair/Fuel Tank Pressure Sensor Replacement (2500 Series))Fuel Tank Pressure Sensor Replacement (1500 Series) (
See: Powertrain Management/Computers and Control Systems/Fuel Tank Pressure Sensor/Service and Repair/Fuel Tank Pressure Sensor
Replacement (1500 Series))Fuel Tank Pressure Sensor Replacement (1500 SWB - 98.4L (26 gal) Tank + E85) (See: Powertrain
Management/Computers and Control Systems/Fuel Tank Pressure Sensor/Service and Repair/Fuel Tank Pressure Sensor Replacement (1500
SWB - 98.4L (26 Gal) Tank + E85))
* Manifold Absolute Pressure Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Manifold
Pressure/Vacuum Sensor/Service and Repair)
No comments:
Post a Comment