2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2163
monitor the TAC system data. Both processors monitor the other processors data to verify that the indicated APP calculation is correct. The ECM
performs an intrusive test in order to confirm that the APP signals are not shorted together. The ECM accomplishes this by pulling the APP sensor
2 low momentarily and looking for sensor 1 to also be pulled low.
Conditions for Running the DTCs
P0601, P0604
* The ignition switch is in Run or Crank.
* These DTCs run continuously when the above condition is met.
P0602, P0603, P062F
* The ignition switch is in Run or Crank.
* These DTCs run once per ignition cycle.
P0606, P0607, P060D
* The ignition switch is in Run or Crank.
* The system voltage is more than 6.0 V.
* Reduced Engine Power is not active.
* These DTCs run continuously when the above conditions are met.
P2610
* The intake air temperature is between -40 to +125掳C (-40 to +257掳F).
* DTC P2610 runs once per ignition cycle on ECM power down.
Conditions for Setting the DTCs
The ECM detects an internal failure or incomplete programming for more than 10 s.
Actions Taken When the DTC Sets
* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.
* DTC P0607 is a Type C DTC.
* DTC P2610 is a Type B DTC.
Conditions for Clearing the MIL/DTC
* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.
* DTC P0607 is a Type C DTC.
* DTC P2610 is a Type B DTC.
Diagnostic Aids
Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set.
* Verify that the battery cables are clean and tight, and the battery is fully charged. Refer to Battery Inspection/Test (See: Starting and
Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* Verify the ECM ground circuits do not have an open or high resistance.
* Verify the ECM power circuits do not have an open, short to ground, or high resistance.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Tuesday, November 17, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2163
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment