2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2039
瀚慖f a short to GND or Open status test displays FAULT, test for an open/high resistance or short to ground on the affected IC circuit
terminal C.
瀚慖f a short to volts status test displays FAULT, test for a short to voltage on the affected IC circuit terminal C.
Important: A high resistance on any IC circuit can cause a misfire condition before DTCs P0351-P0358 set.
2. Exchange the affected ignition coil/module with the ignition coil/module of a cylinder that is not affected.
3. Start and run the engine. With a scan tool, monitor the IC circuit parameters and the Misfire Current counters.
瀚慖f the circuit status fault identified or the misfire transfers with the ignition coil/module, replace the ignition coil/module assembly.
瀚慖f the circuit status fault identified or the misfire does not transfer with the ignition coil/module, replace the ECM.
Repair Instructions
* Ignition Coil Replacement (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair)
* Engine Control Module Replacement (See: Powertrain Management/Computers and Control Systems/Engine Control Module/Service and
Repair)
* Engine Control Module Programming and Setup (See: Powertrain Management/Computers and Control Systems/Engine Control
Module/Testing and Inspection)
Repair Verification
Important: An IC circuit fault condition will result in an engine misfire, and under certain driving conditions could possibly overheat the
3-way catalytic converter.
1. Install any components or connectors that have been removed or replaced during diagnosis.
2. Perform any adjustment, programming, or setup procedures that are required when a component or module is removed or replaced.
3. Start and run the engine. With a scan tool, monitor the IC circuit status parameters. All IC circuit status parameters should display OK.
瀚慖f another DTC is present, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) and perform the appropriate diagnostic.
4. To verify that the performance of the catalytic converter has not been affected by the condition that set this DTC, perform the Repair
Verification for DTC P0420 or P0430. Refer to DTC P0420 or P0430 (See: P Code Charts/P0420).
P0352
DTC P0351-P0358
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0351
- Ignition Coil 1 Control Circuit
DTC P0352
- Ignition Coil 2 Control Circuit
DTC P0353
- Ignition Coil 3 Control Circuit
DTC P0354
- Ignition Coil 4 Control Circuit
DTC P0355
- Ignition Coil 5 Control Circuit
DTC P0356
- Ignition Coil 6 Control Circuit
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Thursday, November 12, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2039
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment