2010 Cadillac CTS Sedan AWD V6-3.6L Page 1147

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1147

P2146, P2149, P2152, P2155, P216A, or P216D

The ECM detects the injector high voltage supply circuit is shorted to ground or shorted to a voltage for greater than 4 seconds or for a cumulative

of 30 seconds.

Action Taken When the DTC Sets

DTCs P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277,

P2146, P2149, P2152, P2155, P216A, and P216D are Type B DTCs.

Conditions for Clearing the DTC

DTCs P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277,

P2146, P2149, P2152, P2155, P216A, and P216D are Type B DTCs.

Diagnostic Aids

* The high voltage supply circuits of injectors 2 and 5, and injectors 3 and 6, are paired together with a dual high side driver in the controller.

A short to ground, or a short to voltage, on one of the paired circuits will set a DTC for the companion injector. The ECM will also disable

the high side driver for the affected injectors.

* The high voltage supply circuits of injectors 1 and 4 are not paired together in the controller.

* Performing the fuel injector coil test may help isolate an intermittent condition. Refer to Fuel Injector Solenoid Coil Test (w/LLT) (See:

Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector

Solenoid Coil Test)Fuel Injector Solenoid Coil Test (w/LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Injector/Testing and Inspection).

* If the condition is intermittent, move the related harnesses and connectors, with the engine operating, while monitoring the scan tool Injector

Control Circuit Test Status parameters. An Injector Control Circuit Test Status parameter will change from OK or Not Run to Fault if there is

a condition with the circuit or a connection.

Reference Information

Schematic Reference

Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Fuel System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information. DTC P062B should not set.

瀚慖f DTC P062B failed this ignition, refer to DTC P062B (w/LLT) (See: P Code Charts/P062B).

2. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

3. Engine operating, observe the appropriate scan tool Injector Control Circuit Test Status parameters. Verify the Injector Control Circuit Test

Status parameters display OK or Not Run.

4. Engine operating, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264,

P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277, P2146, P2149, P2152, P2155, P216A, or P216D should not set.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.