Saturday, October 24, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 1395

2010 Cadillac Truck SRX AWD V6-3.0L Page 1395



the fuel injector after 8 crankshaft revolutions when the misfire is not current, if the vehicle is equipped with a manual transmission.



Conditions for Running the DTC



* DTC P0010, P0011, P0013, P0014, P0016, P0017, P0018, P0019, P0020, P0021, P0023, P0024, P0068, P0101, P0102, P0103, P0106,



P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651,



P1516, P2101, P2122, P2123, P2127, P2128 or P2176 is not set.



* The engine speed is between 450-6,600 RPM.



* The evaporative emissions (EVAP) leak detection is not active.



* The delivered torque signal is greater than 5 % at idle.



* The delivered torque signal is between 6-29 % with the transmission in drive.



* The engine coolant temperature (ECT) is between -7 and +127掳C (+19 and +261掳F).



* The ECM is not receiving a rough road signal.



* The fuel level is greater than 11 %.



* The antilock brake system (ABS) and the traction control system (TCS) are not active or detecting rough road.



* Torque Converter Clutch (TCC) is not applied/active.



* The ECM is not in fuel cut-off or decel fuel cut-off mode.



* DTCs P0300 through P0306 run continuously when the above conditions exist for greater than 1,000 engine revolutions. 200 revolutions



after the first failure.



Conditions for Setting the DTC



P0300



The ECM detects a crankshaft rotation speed variation indicating a misfire rate sufficient to cause emissions levels to exceed a predetermined value.



P0301, P0302, P0303, P0304, P0305, P0306



The ECM detects a crankshaft rotation speed variation indicating a single cylinder misfire rate sufficient to cause emissions levels to exceed



mandated standards.



Action Taken When the DTC Sets



* DTCs P0300-P0306 are Type B DTCs.



* The ECM disables the fuel injector of the misfiring cylinder when a misfire is present.



Conditions for Clearing the DTC



DTCs P0300-P0306 are Type B DTCs.



Diagnostic Aids



* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect for the following possible sources:



- A tire or wheel that is out of round or out of balance



- Variable thickness brake rotors



- An unbalanced drive shaft



- Certain rough road conditions



- Transmission operation



- A damaged accessory drive component or belt; remove the belt and safely operate the engine to evaluate



* High resistance in the circuits of the injectors may set a misfire DTC without setting an injector DTC. Test the injector circuits of the affected



cylinder(s) for a high resistance if you suspect a condition.



* If the condition is intermittent, observing the scan tool IC Circuit Test and Fuel Injector Circuit Test Status parameters may help isolate the



condition. The circuit test status parameters will change from OK or Not Run to Fault if a condition exists.



* A condition in the heated O2 sensor (HO2S) heater control circuits may set a DTC P0300.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

No comments:

Post a Comment