2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 470
Ignition ON, observe the scan tool Mirror Horizontal Position and Mirror Vertical Position parameters. The reading should be between 0.2-4.8 volts
and change as the mirror is moved, left, right, up, and down.
Circuit/System Testing
1. Ignition OFF, disconnect the X7 harness connector at the appropriate door module.
2. Ignition ON, verify a test lamp does not illuminate between the following circuit terminals and ground:
* 5-volt reference circuit terminal 7
* Signal circuit terminal 4
* Signal circuit terminal 5
* Low reference circuit terminal 10
瀚慖f the test lamp illuminates, test the appropriate circuit for a short to voltage.
3. Ignition OFF, test for infinite resistance between the following circuits and ground:
* 5-volt reference circuit terminal 7
* Signal circuit terminal 4
* Signal circuit terminal 5
* Low reference circuit terminal 10
瀚慖f less than the specified value, test the appropriate circuit for a short to ground.
4. Test for 4K-7K ohms between the 5-volt reference circuit terminal 7 and the low reference circuit terminal 10.
瀚慖f not within the specified range, test the 5-volt reference circuit and the low reference circuit for an open/high resistance. If the circuits
test normal, test or replace the rearview mirror.
5. Test for 1K-7K ohms between the 5-volt reference circuit terminal 7 and the signal circuit terminal 4.
瀚慖f not within the specified range, test the signal circuit for an open/high resistance. If the circuits test normal, test or replace the rearview
mirror.
6. Test for 1K-7K ohms between the 5-volt reference circuit terminal 7 and the signal circuit terminal 5.
瀚慖f not within the specified range, test the signal circuit for an open/high resistance. If the circuits test normal, test or replace the rearview
mirror.
7. If all circuits test normal, replace the door module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Outside Rearview Mirror Motor Replacement (See: Body and Frame/Mirrors/Power Mirror Motor/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for DDM or PDM replacement, setup, and
programming
B1600
DTC B1544, B1600, or B1605
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1544 01
- Mirror Motors Common Circuit Short to Battery
DTC B1544 02
- Mirror Motors Common Circuit Short to Ground
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Saturday, September 5, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 470
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment