2010 Cadillac CTS Sedan AWD V6-3.0L Page 1845

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1845

* If the Throttle Sweep Test is not available on the scan tool, observe the scan tool TP Sensor 1 and 2 Agree/Disagree parameter while

performing the following tests:

- Slowly depress the accelerator pedal to WOT and then slowly return the pedal to closed throttle. Repeat the procedure several times.

- Rapidly depress the accelerator pedal from the rest position to the wide open throttle position (WOT) and release pedal. Repeat the

procedure several times.

The TP Sensor 1 and 2 Agree/Disagree parameter should display Agree. If Disagree is displayed, continue diagnosis in Circuit/System

Testing.

* A high resistance condition on the throttle position and throttle actuator control circuits could cause a DTC to set.

Reference Information

Schematic Reference

Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and

Operation/Throttle Actuator Control (TAC) System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify DTC P06A3 is not set.

瀚慖f the DTC is set, refer to DTC P0641, P0651, P0697, or P06A3 (ECM, LF1) (See: P Code Charts/P0641).

2. Ignition ON, observe both TP Sensor voltage parameters with a scan tool. Verify the scan tool TP sensor parameters are between 1.0-4.0 V

and change with accelerator pedal input.

Note: If the Throttle Sweep Test is not available on the scan tool, use the accelerator to perform the test. Refer to Diagnostic Aids for further

details.

3. Perform the Throttle Sweep Test while observing the TP Sensor 1 and 2 Agree/Disagree parameter with a scan tool. The TP Sensor 1 and 2

Agree/Disagree parameter should display Agree.

4. Observe the DTC Information with a scan tool. DTCs P0121, P0122, P0123, P0222, P0223, and P2135 should not set.

5. Observe both TP Sensor percentage parameters while quickly pressing the accelerator pedal from a closed throttle to WOT. Both TP Sensor

percentage parameters should change.

6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the throttle body assembly.

2. Ignition OFF for 1 minute, test for less than 5 ohm between the low reference circuit terminal C and ground.

瀚慖f greater than the specified range, test the low reference circuit for a short to voltage, or an open/high resistance. If the circuit tests

normal, replace the ECM.

3. Ignition ON, test for 4.8-5.2 V between the 5-volt reference circuit terminal E and ground.