Skip to main content

A/C - No Or Insufficient Heat When Temp. Set To MAX SI B64 03 11 Heating and Air Conditioning


Technical Service Bulletin # 640311 Date: 110301
A/C - No Or Insufficient Heat When Temp. Set To MAX
SI B64 03 11
Heating and Air Conditioning
March 2011
Technical Service
SUBJECT
No or Insufficient Heat when the Temperature Is Set to Maximum
MODEL
E90, E91, E92, E93 (3 Series)
SITUATION
There is no or insufficient heat when the temperature is set to maximum. After the vehicle has reached operating temperature, the temperature of the
air coming out from all the vents is not hot.
CAUSE
This could be caused by various issues, such as:
^ Coolant insufficiently filled
^ Clogged heater core or blocked radiator and/or hoses
^ Mixing flaps/stratification flap operating incorrectly
^ Ventilation temperature sensor
^ Footwell temperature sensor faulty
^ Interior temperature sensor faulty
^ Water valve not functioning correctly
2010 BMW 328i Sedan (E90) L6-3.0L (N51)   43
^ IHKA (Integrated Heating and Air Conditioning, automatic) sending incorrect signal
PROCEDURE
Perform the following steps:
1. Verify the performance of the heater using a thermometer to measure the air temp at the vents (Defrost and Footwell). Compare to a known good
vehicle. If heater performance is insufficient when compared to a similar known good vehicle, proceed to the next step.
2. Perform a vehicle test using ISTA (Integrated Service Technical Application) and complete all related test plans if fault codes are stored.
3. The temperature comparison in steps 4 and 5 must be done as follows:
^ While the vehicle is idling in the shop
^ During a test drive
4. Check the engine and radiator temperature and compare readings to a similar known good vehicle (ISTA ECU functions).
5. Using a thermometer, compare the vent temperature readings to that of a similar known good vehicle. This can also be done via Function
Structure/Heating and air conditioning functions/Start search.
^ Select test plan AT6450_KAEKL from the list and click Display.
^ Option 5 - Display system values
6. Check the auxiliary water pump for correct operation (ISTA ECU component activation). If equipped with a water valve, disconnect the electrical
connector from the water valve and monitor the vent temperature, as stated in step 5.
7. If the water valves and water pump are operating correctly, but there is still insufficient heat, a visual inspection of the heater core is needed.
Caution:
Allow the vehicle to cool down before proceeding to the next step.
8. Disconnect the heater hoses entering the passenger compartment (at the bulkhead). Flush the heater core using a water hose. This must be done in
both directions. Collect the dispensed water in a bucket and check for contaminants such as sand, etc.
9. If no contaminants are found during backflushing of the heater core and the water flow is good, retest the heater function during a test drive.
Verify all temperatures in steps 3, 4 and 5. If the heater is working as designed, release the vehicle.
10. If contaminants are collected or the water flow through the heater core circuit is restricted, proceed to the next step.
11. Refer to REP "6411208 Replacing Heat Exchanger" for replacing the heater core.
12. If further assistance is required, submit a PuMA case.
Note:
Search for related test plans under Function structure/Body/Heating and air conditioning functions/Start search. This will display all available test
plans if no faults are stored.
WARRANTY INFORMATION
This service information bulletin is intended to provide technical diagnostic and/or repair information.
Claims that result from the repair of a verified defect are to be processed following established warranty policies and procedures.
Refer to the KSD2 to code the repair(s) performed as determined by the diagnosis.

Comments

Popular posts from this blog

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948) A L L Diagnostic Trouble Codes ( DTC ): P Code Charts P1240

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948)     A L L  Diagnostic Trouble Codes ( DTC ): P Code Charts P1240 The CAN bus is malfunctioning.   Test 1: Check the CAN communication with control unit Engine control module.   Test 2: Possible cause: - Drive train CAN bus Affected functions: - Engine diagnosis - Fuel system 1. Check the CAN communication with control unit Engine control module. Important note A CAN timeout fault code is set due to the absence of a CAN input signal.The cause of this may be not only the transmitter control unit, but also the CAN networking.Possible cause and remedy - Check CAN communication with affected control unit. - Check other control units for vehicle CAN bus failure in the stored faults. - CAN bus has loose contact or Open circuit. Continue with button F 2 Warning!Communication with ECU required. 2. No further information available.

2019 Mercedes-Benz X-Class

Launched for the brand new 3-Series coupe and convertible and provided on all engine variants, M Sport cars include a raft of extra equipment as standard compared to an SE model. Furthermore, passive safety is offered thanks to standard tools akin to seven airbags and the i-Size attachment system for 2 little one seats. Standard safety gear includes antilock disc brakes, stability and traction management, aspect airbags, side curtain airbags, knee airbags and Mercedes-Benz's "mbrace" emergency telematics system. The SLS is supposed to be Mercedes-Benz's ultimate vehicle, however it is also meant to be extra affordable and sensible to drive than the now-discontinued Mercedes SLR McLaren. Twelve (more than one-third) of the above differences are in the double digits. Although the price is affordable or not, are the primary disadvantages of space and rear seats for Mercedes-Benz C-Class 220 CDI vibration motor in the city. In case your body kit includes entrance and/or r...

Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601 30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input

 Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601   30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input Topic number LI80.57-P-051521 Version 1 Design group 80.57 Drive authorization systems (DAS) Date 06-01-2011 Validity All 204, 207 model vehicles Reason for change Complaint 1. No crank / no start / intermittent no crank 2. Communication via SDS to Electronic Ignition Switch N73 (EIS/EZS), and or short test may or may not be possible at time of fault 3. Below scenario: ^ When accessing the occupants compartment, the message center in the ICM will illuminate (note: eventually the message center will time out and shut down, and will not illuminate until the CAN is activated via the interior lock/unlock switch). ^ The key will turn in EIS N73. ^ The ESL N26/5 does not activate/respond (or the steering wheel remains unlocked at all times). ^ The warning icons in the ICM will not il...

2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 2499

2.1.3.2.1.4. Check power supply at control unit N15/3 (ETC [EGS] control unit). Test 2.1.3.2.1.4.1: Guided test 2.1.3.2.1.4.1. Guided test Operation number of operation texts and work units or standard texts and flat rates:27-0641Possible cause - Battery has incorrect charge state or is faulty. - Local undervoltage of component N15/3 (ETC [EGS] control unit) Test sequence - Erase fault memory. Continue with button "F2" Warning!Communication with ECU required. 2.1.3.2.1.5. Check power supply at control unit N15/5 (Electronic selector lever module control unit). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test sequence - Switch off ignition. - Disconnect connector at component N15/5 (Electronic selector lever module control unit). - Switch on ignition. - [A.2] Measure direct voltage with multimeter between 2 and 1 [A.1] Status of relevant actual value: - Supply voltage (tml. 15):Warning! Communication with ECU required. Specified ...

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240 Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)). * Missing, restricted, or leaking exhaust components-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust). * Malfunctioning fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection). * Vacuum hoses for splits, kinks, and improper connections * Insufficient fuel in the tank * Low fuel pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Test...

Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus

Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus Affected functions: CAN Communication Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit N80 (Steering column module). Test 3: Interior CAN check Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage How do I quickly reach my goal? How do I quickly reach my goal?First call up menu item 'Evaluation of CAN...

Relay 'Circuit 87' ( Engine ) (P2505)

P2505 Relay 'Circuit 87' ( Engine ) (P2505) Possible cause: ­ N3/10 (ME­SFI [ME] control unit) ­ K40/4kK (Engine electronics and chassis relay) Affected functions: ­ Battery / On­board electrical system ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 2: Arrangement of fuses Page 2562010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 257 1. Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 1.1: Test voltage supply of circuit 87. 1.1. Test voltage supply of circuit 87. Figure legend ­ A ­ConnectionTest cable 35­pin socket box ­ 001 ­Sockets of component N3/10 (ME­SFI [ME] control unit) ­ 05 ­35­pin socket box ­ 050 ­126­pin socket box ­ 108 ­Test cable 266 589 01 63 00 ­ N3/10 (ME­SFI [ME] control unit) ­ II 1­63ConnectionTest cable ­ III 64­126ConnectionTest cable Warning! ­ ­ Connection A of test ca...

A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit

Mercedes-Benz Mercedes Benz OEM Parts Mercedes Benz OE Replacement Parts Technical Service Bulletin # LI27-57_P-0534962 Date: 120522 2010 Mercedes Benz SL 550 (230.471) V8-5.5L (273.965)   Page 29 A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit Topic number LI27.57-P-053496 Version 2 Design group 27.57 Oil pump Date 05-22-2012 Validity NAG2 FEPlus (722.9) with auxiliary oil pump with code B03 up to transmission sequence number 7.248.200 Reason for change Model series 251 deleted because model series 251 does not have ECO start/stop. Complaint: ECO start/stop inoperative, fault code P0944 in transmission control unit. Attachments Cause: Check valve in torque converter housing may be damaged. Leakage between torque converter housing and auxiliary oil pump. May affect transmissions with transmission sequence numbers starting with -07-xxx xxx. Remedy: Access v...

Mercedes Benz SLK 55 AMG No CAN message was received from control unit Engine management.

2010 Mercedes Benz SLK 55 AMG (171.473) V8-5.5L (113.989) Copyright ? 2013, ALLDATA 10.52SS Page 1 A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Part 1 No CAN message was received from control unit Engine management. Possible cause: - Fault in CAN communication with control unit Motor electronics. - Drive train CAN bus Affected functions: - CAN Communication - Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit Engine management. Test 3: Drive train CAN test 1. Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options 1.1. Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage 1.1.1. How do I quickly reach...