2010 Cadillac Truck Escalade RWD V8-6.2L Page 1387
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B97
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B97
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
Comments
Post a Comment