2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1466

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1466

The ECM detects an internal failure or incomplete or incorrect programming.

Action Taken When the DTC Sets

* DTCs P0602, P0603, P0604, P0605, P0606, P0610, P0614, P0630, P160D, and P160E are Type A DTCs.

* DTCs P06D1 and P2610 are Type B DTCs.

* DTC P161C is a Type C DTC.

Conditions for Clearing the DTC

* DTCs P0602, P0603, P0604, P0605, P0606, P0610, P0614, P0630, P160D, and P160E are Type A DTCs.

* DTCs P06D1 and P2610 are Type B DTCs.

* DTC P161C is a Type C DTC.

Diagnostic Aids

Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set. Verify the following:

* The battery cables are clean and tight, and the battery is fully charged. Refer to Battery Inspection/Test (See: Starting and Charging/Testing

and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* The ECM ground circuits do not have an open or high resistance.

* The ECM power circuits do not have an open, short to ground, or high resistance.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0602, P0603, P0604, P0605, P0606, P0610, P0614, P0630, P06D1, P160D, P160E,

P161C, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition ON, clear the DTC information with a scan tool. Observe the scan tool DTC information.

瀚慖f DTC P0602, P0610, P0614, P0630, P160D, P160E, or P161C failed this ignition, reprogram the K20 ECM. Refer to Control Module

References (See: Testing and Inspection/Programming and Relearning). If the DTC resets, replace the K20 ECM.

2. Observe the DTC information with a scan tool. Verify DTC P0603, P0604, P0605, P0606, P06D1, or P2610 does not set.

瀚慖f a DTC failed this ignition, replace the K20 ECM.