Sunday, March 1, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1265

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1265



Conditions for Clearing the DTC



DTCs P0326, P0327, P0328, P0331, P0332, and P0333 are Type B DTCs.



Diagnostic Aids



* Inspect the knock sensor for physical damage. A knock sensor that is dropped or damaged may cause a DTC to set.



* Inspect the knock sensor for proper installation. A knock sensor that is loose or over torqued may cause a DTC to set. The knock sensor



should be free of thread sealant. The knock sensor mounting surface should be free of burrs, casting flash, and foreign material.



* The knock sensor must be clear of hoses, brackets, and engine electrical wiring.



* With the knock sensor disconnected, the normal voltage measured from the knock sensor signal or the low reference circuit to ground is



between 2.30-2.80 V.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Knock Sensor System Description (See: Powertrain Management/Computers and Control Systems/Knock Sensor/Description and Operation)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Engine at operating temperature, all accessories OFF. Engine speed greater than 2,000 RPM, observe the appropriate scan tool knock sensor



signal voltage parameter. The voltage should be greater than 4.0 V.



2. Engine idling, move the related harnesses and connectors for the knock sensor circuits while observing the scan tool knock sensor signal



voltage parameters. The voltage should remain steady with no abrupt changes.



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, disconnect the harness connector at the appropriate B68 knock sensor.



Note: If the voltage is not within the specified range on either circuit, test for a wire to wire short, short to ground, or short to voltage



between the knock sensor circuits.



2. Ignition ON, test for 2-3 V between the signal circuit terminal A or 1 and ground.



瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuits/connections test



normal, replace the K20 ECM.



瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuits/connections test normal, replace the K20



ECM.



3. Test for 2-3 V between the low reference circuit terminal B or 2 and ground.



瀚慖f less than the specified range, test the low reference circuit for a short to ground or an open/high resistance. If the circuits/connections

No comments:

Post a Comment