2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2614
DTCs P0711, P0712, and P0713 are Type C DTCs.
Diagnostic Aids
During a road test, the transmission fluid temperature (TFT) should steadily increase to a normal operating temperature, and then stabilize.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
* Component Connector End Views (See: Diagrams/Connector Views)
* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Description and Operation
* Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Electronic Component Description)
* Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Transmission General Description)
* Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Transmission Component and System Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Engine idling at normal operating temperature, verify the scan tool Trans Fluid Temp. parameter is between -74 and +174掳C (-101 and +345掳
F).
瀚慖f not within the specified range, replace the Q8 control solenoid valve assembly.
2. Operate the vehicle at 64 km/h (40 mph) for 10 minutes. Monitor the Transmission Fluid Temperature parameter and the TCM Temperature
parameter with a scan tool. The Transmission Fluid Temperature parameter should increase by more than 2掳C (3.5掳F). Also, the
Transmission Fluid Temperature parameter and the TCM Temperature parameter should be within 10掳C (18掳F) of each other.
瀚慖f the Transmission Fluid Temperature parameter does not increase by more than 2掳C (3.5掳F) or the Transmission Fluid Temperature
parameter is not within 10掳C (18掳F) of the TCM Temperature parameter, then replace the Q8 control solenoid valve assembly.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control solenoid valve assembly replacement. Refer to Control Module References (See: Testing and Inspection/Programming and
Relearning) for replacement, setup, and programming.
* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Programming and Relearning) following all transmission related repairs.
No comments:
Post a Comment