2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2633
Diagnostic Aids
Inspect the ISS/OSS, harness, connector and control solenoid valve assembly for metallic debris and output shaft housing machined slots for
damage or misalignment. Proper torque of the ISS/OSS mounting bolt is critical to proper speed sensor operation.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
* Component Connector End Views (See: Diagrams/Connector Views)
* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Description and Operation
Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Electronic Component Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
DT-47825-10 - Jumper Harness
For equivalent regional tools, refer to Special Tools (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Tools and
Equipment/6L45/6L50/6L80/6L90 - Automatic Transmission).
Circuit/System Verification
1. Ignition ON, verify with a scan tool the transmission ISS/OSS supply voltage test status parameter displays OK.
2. Operate the vehicle at 16-32 km/h (10-20 mph) while observing the Transmission OSS parameter on the scan tool. The Transmission OSS
parameter should vary with the vehicle speed and not drop out.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Note: You must perform the Circuit/System Verification first.
1. Ignition OFF, remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly
Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and
Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).
2. Connect the DT-47825-10 - jumper harness between the vehicle wire harness electrical connector, and the control solenoid valve assembly
electrical connector.
3. Ignition ON, test for 8.3-9.3 volts between the ISS/OSS voltage circuit terminal B on the Q8 control solenoid valve assembly and ground at
the transmission case.
瀚慖f not within the specified range, replace the control solenoid valve assembly.
4. Perform the Control Solenoid Valve and Transmission Control Module Assembly Input Shaft Speed/Output Shaft Speed Input Test (See:
Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General
Diagnostics/6L45/6L50/6L80/6L90 - Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Input
Shaft Speed/Output Shaft Speed Input Test).
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Wednesday, February 26, 2020
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2633
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment