Saturday, February 22, 2020

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2537

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2537

Action Taken When the DTC Sets

* DTCs P0601, P0602, P0603, P0604, and P062F are Type A DTCs.

* The TCM shifts to a default gear, shuts down, and turns OFF.

Conditions for Clearing the DTC

DTCs P0601, P0602, P0603, P0604, and P062F are Type A DTCs.

Reference Information

Description and Operation

Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Electronic Component Description)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

1. Ignition OFF for one minute.

Caution: Before programming a control module, the following must be observed, or control module damage may occur:

* The scan tool and the terminal must have the latest software.

* The vehicle battery must be fully charged. The battery voltage should be between 12-14 volts.

* The scan tool and the terminal cable connections must be secure.

* A battery charger must NOT be connected to the battery when programming a control module.

2. Ignition ON, with a scan tool verify that DTC P0602 is not set.

瀚慖f DTC P0602 is set, program the transmission control module. Refer to Service Programming System (SPS) (See: Testing and

Inspection/Programming and Relearning/Service Programming System (SPS)) and Control Solenoid Valve and Transmission Control

Module Assembly Programming and Setup (2ML70) (See: Powertrain Management/Transmission Control Systems/Relays and Modules

- Transmission and Drivetrain/Relays and Modules - A/T/Control Module/Testing and Inspection/2ML70 - Automatic Transmission

)Control Solenoid Valve and Transmission Control Module Assembly Programming and Setup (6L45/6L50/6L80/6L90) (See:

Powertrain Management/Transmission Control Systems/Relays and Modules - Transmission and Drivetrain/Relays and Modules -

A/T/Control Module/Testing and Inspection/6L45/6L50/6L80/6L90 - Automatic Transmission).

3. Verify with a scan tool that DTCs P0601, P0603, P0604, or P062F are not set.

瀚慖f DTCs P0601, P0603, P0604, or P062F are set, replace the control solenoid valve and transmission control module assembly.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and

Inspection/Programming and Relearning) following all transmission related repairs.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,

setup, and programming.

Hybrid Controls

DTC P0601-P0604, P0606, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

No comments:

Post a Comment