Thursday, January 2, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1107

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1107



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Engine idling, observe the scan tool HO2S 2 voltage parameter. The reading should fluctuate above and below the range of 350-550 mV.



2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, disconnect the harness connector at the B52 HO2S 2.



2. Ignition ON, verify that the scan tool HO2S 2 voltage parameter is between 350-500 mV.



瀚慖f less than the specified range, test the signal circuit terminal 4 for a short to ground. If the circuit/connections test normal, replace the



K20 ECM.



瀚慖f greater than the specified range, test the signal circuit terminal 4 for a short to voltage. If the circuit/connections test normal, replace the



K20 ECM.



3. Connect a 3 A fused jumper wire between the signal circuit terminal 4 and ground. Verify the scan tool HO2S voltage parameter is less than



60 mV.



瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit/connections test normal, replace the



K20 ECM.



4. Connect a 3 A fused jumper wire between the signal circuit terminal 4 and the low reference circuit terminal 3. Verify the scan tool HO2S 2



voltage parameter is less than 60 mV.



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the



circuit/connections test normal, replace the K20 ECM.



5. Verify that the following conditions do not exist:



* Lean, rich, or leaking fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and



Air Induction/Fuel Injector/Testing and Inspection/Fuel Injector Solenoid Coil Test)Fuel Injector Solenoid Coil Test (LF1, LFW) (See:



Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection/Fuel Injector Solenoid Coil Test).



* A fuel pressure that is too low or too high-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery



and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:



Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel



System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel



System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air



Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).



* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery



and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel

No comments:

Post a Comment