2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1944

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1944

Conditions for Running the DTC

P2714

* No DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207,

P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, or P182E.

* The ignition voltage is 8.6 volts or greater.

* The output speed is 16 RPM or greater, or the throttle position is 0.4 percent or greater.

* The throttle position signal is valid.

* The engine speed is greater than 400 RPM for 5 seconds.

* The transmission fluid temperature is 0掳C (32掳F) or greater.

* 2-6 clutch is commanded ON.

* The high side driver is enabled.

P2715

* No DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207,

P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, or P182E.

* The ignition voltage is 8.6 volts or greater.

* The high side driver is enabled.

* The transmission fluid temperature is 0掳C (32掳F) or greater.

* The transmission output shaft speed is 350 RPM or greater.

* The transmission input shaft speed is 200 RPM or greater.

* The 2-6 clutch is commanded OFF.

Conditions for Setting the DTC

P2714

The TCM detects an incorrect on-coming clutch gear ratio, or flare, when the 2-6 clutch is commanded ON and the transmission input shaft speed is

200 RPM or greater from the anticipated input shaft speed for 2 seconds, a total of 3 times in second gear, or a total of 3 times in sixth gear.

P2715

The TCM detects an incorrect off-going clutch gear ratio, or tie-up, when the 2-6 clutch is commanded OFF and the transmission input shaft speed

is 40 RPM or less from the anticipated input shaft speed for 1.2 seconds, a total of 3 times from second gear or a total of 3 times from sixth gear.

Action Taken When the DTC Sets

P2714

* DTC P2714 is a Type A DTC.

* The TCM commands maximum line pressure.

* The TCM inhibits Tap Up/Down function.

* The TCM inhibits manual shifting of forward gears.

* The TCM freezes transmission adaptive functions.

* The TCM limits the transmission to first, third, or reverse operation.

P2715

* DTC P2715 is a Type A DTC.

* The TCM commands maximum line pressure.

* The TCM inhibits Tap Up/Down function.

* The TCM inhibits manual shifting of forward gears.

* The TCM freezes transmission adaptive functions.

* The TCM limits the transmission to second gear operation.

Conditions for Clearing the DIC/DTC

DTCs P2714 and P2715 are Type A DTCs.

Diagnostic Aids

Before performing a road test, configure and setup the scan tool for snapshot mode. This will allow you to display, monitor, and verify multiple

transmission data parameters at one time, after the road test.

Reference Information

Connector End View Reference

* Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

* Inline Harness Connector End Views (See: Diagrams/Connector Views/Multiple Junction Connector/Connector End Views By Number)

Description and Operation