2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1298

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1298

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, remove the fuse that supplies B+ to terminal 56-X2 of the ECM.

2. Disconnect the harness connector at the appropriate camshaft position sensor.

Note: The control module or the sensor may be damaged if the circuit is shorted to B+ voltage.

3. Test for 5 ohm or less between the low reference circuit terminal 1 and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the

circuit/connections test normal, replace the ECM.

4. Install the fuse that supplies B+ to terminal 56-X2 of the ECM.

5. Ignition ON, test for greater than 4.8 V between the 5-volt reference circuit terminal 3 and ground.

瀚慖f less than the specified value, test the 5-volt reference circuit for an open/high resistance. If the circuits/connections test normal, replace

the ECM.

6. Test for 4.8-5.2 V between the signal circuit terminal 2 and ground.

瀚慖f the voltage is greater than specified range, test for a short to voltage in the signal circuit. If circuit/connections test normal, replace the

ECM.

瀚慖f the voltage is less than the specified range, test for a short to ground or an open/high resistance in the signal circuit. If

circuit/connections test normal, replace the ECM.

7. If all circuits/connections test normal, replace the camshaft position sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

programming

P0348

DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, or P0393 (LAU)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0341

- Intake Camshaft Position Sensor Performance Bank 1

DTC P0342

- Intake Camshaft Position Sensor Circuit Low Voltage Bank 1

DTC P0343

- Intake Camshaft Position Sensor Circuit High Voltage Bank 1