2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1391

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1391

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Evaporative Emission Control System Description (See: Powertrain Management/Computers and Control Systems/Description and

Operation/Evaporative Emission Control System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Command the EVAP vent solenoid valve ON and OFF with the scan tool. An audible click should be heard when changing between the

commanded states.

2. Start the engine, observe the DTC information with a scan tool. DTC P0449, P0498, or P0499 should not set.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the EVAP vent solenoid valve.

2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal A and ground.

瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests

normal and the ignition voltage circuit fuse is open, test all components connected to the ignition voltage circuit and replace as necessary.

3. Ignition OFF, connect a test lamp between the control circuit terminal B and the ignition voltage circuit terminal A.

Important: The control circuit for the EVAP vent solenoid valve is pulled-up to voltage within the ECM, 2.6-4.6 volts on the control

circuit is normal.

4. Ignition ON, use a scan tool to command the EVAP vent solenoid valve ON and OFF. The test lamp should turn ON and OFF.

瀚慖f the test lamp remains ON all the time, test for a short to ground on the control circuit. If circuit/connections test normal, replace the

ECM.

瀚慖f the test lamp remains OFF all the time, test for a short to voltage or an open/high resistance on the control circuit. If circuit/connections

test normal, replace the K20 ECM.

5. Test for 2.6-4.6 volts between the control circuit terminal B and ground.

瀚慖f the voltage is not within the specified range, replace the K20 ECM.

6. If all circuits/connections test normal, test or replace the Q13 EVAP vent solenoid valve.

Component Testing

1. Test for 20-24 ohms between the terminals of the Q13 EVAP vent solenoid valve.

瀚慖f not within the specified range, replace the Q13 EVAP vent solenoid valve.