2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 935
1. Spray the suspected area with a 5 percent saltwater solution. To create a 5 percent saltwater solution, add 2 teaspoons of salt to 8 fl oz of
water (10 g of salt to 200 ml of water).
2. Test drive the vehicle over various road surfaces: bumps, turns, etc., above 40 km/h (25 mph) for at least 30 seconds.
3. Rinse the area thoroughly when completed.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS
Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Observe the scan tool Wheel Speed Sensor parameter. The reading should be the same speed on all sensors when driving in a straight line at a
speed greater than 20 km/h (13 mph).
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the EBCM.
2. Ignition ON, test for less than 1 V between the 12 V reference circuit terminal of the appropriate sensor listed below and ground.
* Left front sensor circuit terminal 28
* Right front sensor circuit terminal 17
* Left rear sensor circuit terminal 4
* Right rear sensor circuit terminal 3
瀚慖f greater than the specified range, test the 12 V reference circuit for a short to voltage.
3. Test for less than 1 V between the signal circuit terminal of the appropriate sensor listed below and ground.
* Left front sensor circuit terminal 29
* Right front sensor circuit terminal 6
* Left rear sensor circuit terminal 5
* Right rear sensor circuit terminal 2
瀚慖f greater than the specified range, test the signal circuit for a short to voltage.
4. Ignition OFF, test for infinite resistance between the 12 V reference terminal of the appropriate sensor circuit listed below and ground.
* Left front sensor circuit terminal 28
* Right front sensor circuit terminal 17
* Left rear sensor circuit terminal 4
* Right rear sensor circuit terminal 3
瀚慖f less than the specified value, test the 12 V reference circuit for a short to ground.
5. Test for infinite resistance between the following signal circuit terminal of the appropriate sensor circuit listed below and ground.
* Left front sensor circuit terminal 29
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Tuesday, December 17, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 935
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment