2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 656
B2880 06
The steering column tilt sensor signal voltage is less than 0.2 volt for more than 2 seconds.
B2880 5A
An incorrect steering column tilt sensor signal voltage is seen.
B2880 61
The steering column tilt sensor signal voltage does not change when the tilt actuator is commanded.
Action Taken When the DTC Sets
Steering column tilt operations are suspended.
Conditions for Clearing the DTC
* A current DTC will clear when the malfunction is no longer present
* A history DTC will clear after 50 malfunction-free ignition cycles.
Reference Information
Schematic Reference
Steering Wheel Schematics (See: Diagrams/Electrical Diagrams/Steering/Steering Column/Steering Wheel Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Steering Wheel and Column Description and Operation (See: Steering and Suspension/Steering/Steering Column/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for Scan Tool Information
Circuit/System Verification
Ignition ON, command the tilt motor UP and DOWN with a scan tool. The reading should be between 0.2 and 4.8 volts.
Circuit/System Testing
Tilt Sensor Circuit Malfunction
1. Ignition OFF, disconnect the harness connector at the tilt actuator.
2. Ignition OFF, test for less than 10.0 ohms between the low reference circuit terminal E and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal D and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the scan tool Tilt Sensor parameter is less than 0.2 volt.
瀚慖f greater than the specified range, test the signal circuit terminal C for a short to voltage. If the circuit tests normal, replace the MSM.
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Wednesday, December 4, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 656
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment