2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 85
3. Ignition ON, transmission in PARK, verify the test lamp does not illuminate.
瀚慖f the test lamp illuminates, test for a short to ground on the park enable signal circuit. If the circuit tests normal and the DTC is current,
replace the BCM.
4. If the circuit tests normal and the DTC is current, test or replace the park enable PCB relay.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Instrument Panel Electrical Center or Junction Block Replacement - Left Side (See: Maintenance/Fuses and Circuit Breakers/Fuse
Block/Service and Repair/Removal and Replacement/Instrument Panel Electrical Center or Junction Block Replacement - Left Side)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming
B008A
DTC B008A or B008B
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC B008A 00
- High Voltage Crash Impact Detection Sensor 2
DTC B008B 00
- High Voltage Crash Impact Detection Sensor 3
Circuit/System Description
The high voltage circuit impact detector sensor utilizes a unidirectional 2-wire circuit. The high voltage circuit impact detector sensor modulates
current on the circuit interface to send ID, state of health, and deployment commands to the serial data gateway module. The serial data gateway
module serves as a power source and a ground for the high voltage circuit impact detector sensor. When the ignition is turned ON and input power
from the serial data gateway module is first detected, the high voltage circuit impact detector sensor responds by performing internal diagnostics
and sending an ID to the serial data gateway module. The high voltage circuit impact detector sensor continually communicates status messages to
the serial data gateway module. Some applications use multiple high voltage circuit impact detector sensors.
This vehicle does not use crash sensor 2 or 3. These DTCs can only set if the incorrect software is installed in the serial data gateway module.
Conditions for Running the DTC
* The ignition is ON.
* The battery voltage is 7.5-18 V.
Conditions for Setting the DTC
B008A 00 or B008B 00
Sensor 2 or 3 is reporting a state-of-health message, but the serial data gateway module is not calibrated to use sensor 2 or 3.
Action Taken When the DTC Sets
The driver information center (DIC) displays the SERVICE HYBRID SYSTEM message.
Conditions for Clearing the DTC
* A current DTC clears when the malfunction is no longer present.
* The DIC message turns OFF when the DTC passes.
* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.
Circuit/System Verification
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Friday, December 13, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 85
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment