2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 887
Conditions for Clearing the DTC
* The condition for setting the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS
Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the EBCM.
2. Test for less than 1 ohm between the ground circuits listed below and ground.
* Terminal 13
* Terminal 38
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp illuminates between the B+ circuits listed below and ground.
* Terminal 1
* Terminal 25
瀚慖f the test lamp does not illuminate, test the appropriate circuit for a short to ground or an open/high resistance. If the circuit tests normal
and the B+ circuit fuse is open, replace the BPMV.
4. If all circuits test normal, replace the BPMV and verify DTC does not reset. If the DTC resets, replace the EBCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Brake Pressure Modulator Valve Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Hydraulic
Control Assembly - Antilock Brakes/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming
C12E8
DTC C0110, C12E0, C12E8, or C12E9
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Sunday, December 15, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 887
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment