Thursday, December 5, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 687

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 687

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the center high mounted stop lamp.

2. Test for less than 5.0 ohm between the ground circuit terminal B and ground.

瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.

3. Connect a test lamp between the control circuit terminal A and the ground circuit terminal B.

4. Ignition ON, turn the stop lamps ON and OFF by applying and releasing the brake pedal. The test lamp should turn ON and OFF when

changing between the selected states.

瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.

瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the BCM.

5. If all circuits test normal, replace the center high mounted stop lamp.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Tail Lamp Bulb Replacement (Yukon) (See: Lighting and Horns/Tail Lamp/Tail Light Bulb/Service and Repair/Tail Lamp Bulb

Replacement (Yukon))Tail Lamp Bulb Replacement (Cadillac) (See: Lighting and Horns/Tail Lamp/Tail Light Bulb/Service and

Repair/Tail Lamp Bulb Replacement (Cadillac))Tail Lamp Bulb Replacement (Tahoe, Avalanche) (See: Lighting and Horns/Tail Lamp/Tail

Light Bulb/Service and Repair/Tail Lamp Bulb Replacement (Tahoe, Avalanche))Tail Lamp Bulb Replacement (Tahoe) (See: Lighting and

Horns/Brake Lamp/Brake Light Bulb/Service and Repair/Tail Lamp Bulb Replacement (Tahoe))Tail Lamp Bulb Replacement (Yukon

Two-mode Hybrid) (See: Lighting and Horns/Brake Lamp/Brake Light Bulb/Service and Repair/Tail Lamp Bulb Replacement (Yukon

Two-mode Hybrid))

* High Mount Stop Lamp Replacement (Yukon Two-mode Hybrid) (See: Lighting and Horns/Center Mounted Brake Lamp/Service and

Repair/High Mount Stop Lamp Replacement (Yukon Two-mode Hybrid))High Mount Stop Lamp Replacement (Yukon) (See: Lighting and

Horns/Center Mounted Brake Lamp/Service and Repair/High Mount Stop Lamp Replacement (Yukon))High Mount Stop Lamp Replacement

(Avalanche) (See: Lighting and Horns/Center Mounted Brake Lamp/Service and Repair/High Mount Stop Lamp Replacement (Avalanche)

)High Mount Stop Lamp Replacement (Escalade) (See: Lighting and Horns/Center Mounted Brake Lamp/Service and Repair/High Mount

Stop Lamp Replacement (Escalade))

* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming

B3567

DTC B3567

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B3567 01

- Driver Information Center (DIC) Select Switch Circuit Short To Battery

DTC B3567 59

- Driver Information Center (DIC) Select Switch Circuit/Component Protection Time-Out

Diagnostic Fault Information

No comments:

Post a Comment