2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1607

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1607

* Measured gear ratio deviates more than 20% from expected ratio.

* Determined after 12 times lasting 1 s or more.

Action Taken When the DTC Sets

* DTC P0736 is a Type C DTC.

* Torque limitation in "D" range 150 Nm (110 lb ft), in "R" range 170 Nm (125 lb ft).

* The TCM freezes transmission adaptive functions.

* The TCM turns OFF all solenoids.

* The TCM allows the vehicle after a stop to operate only in the second gear and "R" range.

Conditions for Clearing the DTC

* DTC P0736 is a Type C DTC.

* Measured gear ratio deviates less than 4% from expected ratio.

Diagnostic Aids

Ensure the transmission fluid level, color and odor is correct and there are no leaks. If there are any other transmission DTCs set, diagnose those

first.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams/Electrical

Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Description and Operation

Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/AF40-6 - Automatic Transmission/Transmission Component and System Description)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Verify the transmission fluid level, color and odor is correct.

2. Operate the vehicle to induce a shift from fifth to sixth gear while observing the following scan tool parameters. The scan tool parameters has

to change the proper value referring to the current gear, compare the proper values with: transmission system description and operation. Refer

to Transmission System Description and Operation (M36 and MXE) (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Description and Operation/AF40-6 - Automatic Transmission/Transmission System Description and Operation (M36

and MXE)). Perform this action 2 times.

* Clutch Pressure Control Solenoid Valve 1 Current

* Clutch Pressure Control Solenoid Valve 2 Current

* Clutch Pressure Control Solenoid Valve 3 Current

* Brake Band Pressure Control Solenoid Valve Current

* Shift Solenoid Valve 1

* Shift Solenoid Valve 2

瀚慖f the scan tool parameter does not change the proper value and no other DTCs than P0729, P0731, P0732, P0733, P0734, P0735, P0736,

P0780, P1731 are set, go to Circuit/System Testing.