2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 476
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Outside Mirror Description and Operation (Heated Mirrors) (See: Body and Frame/Mirrors/Description and Operation/Outside Mirror Description
and Operation (Heated Mirrors))Outside Mirror Description and Operation (Power Mirrors) (See: Body and Frame/Mirrors/Description and
Operation/Outside Mirror Description and Operation (Power Mirrors))
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool References
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.
Circuit/System Verification
Ignition ON, observe the scan tool Mirror Horizontal Position and Mirror Vertical Position parameters. The reading should be between 0.2-4.8 volts
and change as the mirror is moved, left, right, up, and down.
Circuit/System Testing
1. Ignition OFF, disconnect the X7 harness connector at the appropriate door module.
2. Ignition ON, verify a test lamp does not illuminate between the following circuit terminals and ground:
* 5-volt reference circuit terminal 7
* Signal circuit terminal 4
* Signal circuit terminal 5
* Low reference circuit terminal 10
瀚慖f the test lamp illuminates, test the appropriate circuit for a short to voltage.
3. Ignition OFF, test for infinite resistance between the following circuits and ground:
* 5-volt reference circuit terminal 7
* Signal circuit terminal 4
* Signal circuit terminal 5
* Low reference circuit terminal 10
瀚慖f less than the specified value, test the appropriate circuit for a short to ground.
4. Test for 4K-7K ohms between the 5-volt reference circuit terminal 7 and the low reference circuit terminal 10.
瀚慖f not within the specified range, test the 5-volt reference circuit and the low reference circuit for an open/high resistance. If the circuits
test normal, test or replace the rearview mirror.
5. Test for 1K-7K ohms between the 5-volt reference circuit terminal 7 and the signal circuit terminal 4.
瀚慖f not within the specified range, test the signal circuit for an open/high resistance. If the circuits test normal, test or replace the rearview
mirror.
6. Test for 1K-7K ohms between the 5-volt reference circuit terminal 7 and the signal circuit terminal 5.
瀚慖f not within the specified range, test the signal circuit for an open/high resistance. If the circuits test normal, test or replace the rearview
mirror.
7. If all circuits test normal, replace the door module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Tuesday, November 26, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 476
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment