2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 526

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 526

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the HSM.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

8. If all circuits test normal, replace the HSM.

B2180 0A, B2180 0B, B2180 0C, B2180 0D, B2180 0E, B2180 04, or B2180 1F

1. Ignition OFF, disconnect the X1 harness connector at the HSM.

Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat

unoccupied, then with the seat occupied.

2. Test for 3.5 - 11.5 Ohms between control circuit terminal 3 and control circuit terminal 4.

瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat back heater

element.

瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat back

heater element.

3. Disconnect the X2, X4 harness connectors at the HSM.

4. Test for 850 - 300 kOhms between the signal circuit terminal 10 X4 and the low reference circuit terminal 7 X2.

瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat

back heater element/temperature sensor.

瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits

test normal, replace the seat back heater element/temperature sensor.

5. Connect the X1, X2, X4 harness connectors at the HSM.

6. Disconnect the harness connector at the seat back heater element/temperature sensor.

7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the HSM.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

8. If all circuits test normal, replace the HSM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Back Cushion Heater Replacement (Escalade with HP2) ()Driver or Passenger Seat Back Cushion Heater

Replacement (Tahoe with HP2) ()Driver or Passenger Seat Back Cushion Heater Replacement (without HP2) ()

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming

Dealer Installed

DTC B1935 or B2180 (Dealer Installed)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B1935 04

- Left Seat Back Heater Circuit Open

DTC B1935 0A

- Left Seat Back Heater Circuit Rate of Change Below Threshold

DTC B1935 0B

- Left Seat Back Heater Circuit Current Above Threshold