2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 463
* A history DTC will clear after 100 ignition cycles.
Reference Information
Schematic Reference
* Starting and Charging Schematics (See: Starting and Charging/Diagrams/Electrical Diagrams)
* Body Control System Schematics (See: Body and Frame/Body Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Charging System Description and Operation (See: Starting and Charging/Charging System/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Ignition ON, headlamps and all accessories OFF, observe the scan tool BCM Battery Current parameter. The reading should be between -5 amps
and -25 amps, and change with the amount of current draw on the battery.
Circuit/System Testing
1. Ignition ON, observe the scan tool BCM Battery Voltage parameter. The reading should be equal to B+ voltage.
瀚慖f not the specified value, test the following BCM circuits for an open/high resistance. If the circuits test normal, replace the BCM.
* B+ circuit terminal 3 X3
* Ground circuit terminal 1 X3
* Ground circuit terminal 5 X3
* Ground circuit terminal 9 X4
2. Verify that the current sensor is mounted correctly on the 12V battery cable. The sensor should be installed with the internal coil around the
negative battery cables, with the tape tab pointing away from the battery.
瀚慖f the sensor is not installed correctly, remove and reinstall the sensor.
3. Ignition OFF, disconnect the harness connector at the battery current sensor.
4. Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 ohms between the low
reference circuit terminal B and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the BCM.
5. Ignition ON, test for 4.5-5.5 volts between the 5-volt reference circuit terminal A and ground.
瀚慖f not within the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests
normal, replace the BCM.
6. Ignition ON, test for 4.5-5.5 volts between the signal circuit terminal C and ground.
瀚慖f not within the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the BCM.
7. If all circuits test normal, replace the battery current sensor.
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Monday, November 25, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 463
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment