2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 563

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 563

Action Taken When the DTC Sets

The heated seat cushion function for the affected seat will be disabled.

Conditions for Clearing the DTC

* The current DTC clears when the malfunction is no longer present, and the power mode changes to OFF then back to ACC or RUN.

* The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.

Reference Information

Schematic Reference

Heated/Cooled Seat Schematics ()

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Heated Seats Description and Operation (KA1) ()Heated Seats Description and Operation (KA6) ()

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

B2425 0A, B2425 0B, B2425 0C, B2425 0D, B2425 0E, B2425 04, or B2425 1F

1. Ignition OFF, disconnect the X1 harness connector at the HSM.

Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat

unoccupied, then with the seat occupied.

2. Test for 2.0 - 8.0 Ohms between control circuit terminal 3 and control circuit terminal 5.

瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater

element.

瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal replace the seat cushion

heater element.

3. Disconnect the X2, X4 harness connectors at the HSM.

4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 9 X4 and the low reference circuit terminal 6 X2.

瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat

cushion heater element/temperature sensor.

瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits

test normal, replace the seat cushion heater element/temperature sensor.

5. Connect the X1, X2, X4 harness connectors at the HSM.

6. Disconnect the harness connector at the seat cushion heater element/temperature sensor.

7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the HSM.

8. If all circuits test normal, replace the HSM.

B2430 0A, B2430 0B, B2430 0C, B2430 0D, B2430 0E, B2430 04, or B2430 1F

1. Ignition OFF, disconnect the X1 harness connector at the HSM.