2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 503
The heated mirror will be disabled.
Conditions for Clearing the DTC
* A current DTC will clear when the fault is no longer present.
* A history DTC will clear after 40 fault free ignition cycles.
Reference Information
Schematic Reference
Outside Rearview Mirror Schematics (See: Body and Frame/Mirrors/Diagrams/Electrical Diagrams/Outside Rearview Mirror Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Outside Mirror Description and Operation (Heated Mirrors) (See: Body and Frame/Mirrors/Description and Operation/Outside Mirror Description
and Operation (Heated Mirrors))Outside Mirror Description and Operation (Power Mirrors) (See: Body and Frame/Mirrors/Description and
Operation/Outside Mirror Description and Operation (Power Mirrors))
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool References
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.
Circuit/System Verification
Ignition ON, press the rear window defogger switch. The rear window defogger and both heated mirrors should become warm.
Circuit/System Testing
1. Ignition OFF, disconnect the X3 harness connector at the appropriate door module.
2. Ignition ON, verify a test lamp does not illuminate between the control circuit terminal 7 and ground.
瀚慖f the test lamp illuminates, test the control circuit for a short to voltage.
3. Ignition OFF, test for infinite resistance between the control circuit terminal 7 and ground.
瀚慖f less than the specified value, test the control circuit for a short to ground. If the circuit tests normal, test or replace the applicable
rearview mirror face.
4. Test for 5-10 ohms of resistance between the control circuit terminal 7 and the low reference circuit terminal 3.
瀚慖f not within the specified range, test the control circuit and the low reference circuit for an open/high resistance. If the circuits test
normal, test or replace the appropriate rearview mirror face.
5. If all circuits test normal, test or replace the door module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Outside Rearview Mirror Glass Replacement (See: Body and Frame/Mirrors/Service and Repair/Outside Rearview Mirror Glass
Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for DDM or PDM replacement, setup and
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Wednesday, November 13, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 503
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment