2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1263

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1263

DTC P0BD9

- Drive Motor Inverter Temperature Sensor 4 Circuit High Voltage

DTC P0BDC

- Drive Motor Inverter Temperature Sensor 5 Performance

DTC P0BDD

- Drive Motor Inverter Temperature Sensor 5 Circuit Low Voltage

DTC P0BDE

- Drive Motor Inverter Temperature Sensor 5 Circuit High Voltage

DTC P0BE1

- Drive Motor Inverter Temperature Sensor 6 Performance

DTC P0BE2

- Drive Motor Inverter Temperature Sensor 6 Circuit Low Voltage

DTC P0BE3

- Drive Motor Inverter Temperature Sensor 6 Circuit High Voltage

Circuit/System Description

This is an internal fault detection of the drive motor generator power inverter module (PIM) assembly. This fault is handled inside the PIM and no

external circuits are involved.

Conditions for Running the DTC

P0AEE, P0AF3, P0BD2, P0BD7, P0BDC, and P0BE1

* Ignition ON after the ignition has been OFF for 6 hours.

* Temperature average of the inverter phase temperature sensors is greater than 12掳C (10掳F).

* Motor temperature sensor is greater than -40掳C (-40掳F).

* DTCs P0AEF, P0AF0, P0BD3, P0BD4, P0BDD, P0BDE, P0A2C, and P0A2D are not set.

P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2

Ignition ON.

P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3

* Ignition ON.

* Motor temperature is greater than -40掳C (-40掳F).

瀚慖f motor temperature is less than -40掳C (-40掳F) at Ignition ON, the drive motor must operate at greater than 20 Nm (14.75 lb ft) for a

cumulative time of 1.5 minutes before the DTC will run.

Conditions for Setting the DTC

P0AEE, P0AF3, P0BD2, P0BD7, P0BDC, and P0BE1

* A 15掳C ( 27掳F) difference is observed between the individual inverter phase temperature sensor and the average of all the inverter phase

temperatures.

* The above condition is present for 4 seconds.

P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2

The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.

P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3

The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.

Action Taken When the DTC Sets

* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,

P0BE1, P0BE2 AND P0BE3 are Type B DTCs.

* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.

Conditions for Clearing the DTC

DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,